Consider a general point on the line joining the 2 wires

Assignment Help Mechanical Engineering
Reference no: EM13962385

1530_line.png

Figure 1 for use with the following questions.

D1 = 10cm, D2 = 10 cm

i1 = 1 amp current into page, i2 = 1 amp,

Question a)

Two wires of infinite length are placed at a distance D = 10cm on opposite sides of a point O, both wires carry the same current of 1.0 A, in which direction must this current flow in order for the magnetic field strength at O to be non-zero.

Question b)

Consider a general point on the line joining the 2 wires and a distance d away from the mid point O.

By summing the magnetic field due to currents of magnitude i flowing in both wires in the sense you found in (a), show that, on the line joining the two wires, the magnetic field strength is given by:

1740_df.png

(Hint you may find the identity (a + b)(a - b) = a2- b2 useful)

Question c)

An electron is traveling at 5.0 x 106 m s-1 directly into the page at the point P shown in figure 1. P is 4.0 cm from O. Again D = 10 cm and the currents i in both wires have magnitudes of 1.0 A and are flowing in the directions given and found in question

(a). find the magnitude and direction of the force that the electron experiences.

Reference no: EM13962385

Questions Cloud

Why is coax cable used in some applications : find the magnetic field in the space between the wire and the sleeve; and also in the space outside the sleeve. (that is , find the mag field at a distance 'r' from the center of the wire when b c )
Describe the changes you would like to see and why : On a PowerPoint Presentation show a picture of the product that you would like to see revamped. Describe the changes you would like to see and why
What is the force per length exerted by i2 on i1 : Two long, parallel conductors, separated by 10.0 cm, carry currents in the same direction. The first wire carries current I1 = 5.00 A and the second carries I2 = 8.00 A.
Compare and contrast licensing and investment in general : Suppose you are five (5) years into exporting shoes to your chosen country, and have decided to try a new global strategy. Compare and contrast licensing and investment in general, and select one (1) for your new strategy. Support your decision wi..
Consider a general point on the line joining the 2 wires : Two wires of infinite length are placed at a distance D = 10cm on opposite sides of a point O, both wires carry the same current of 1.0 A, in which direction must this current flow in order for the magnetic field strength at O to be non-zero.
Write marketing plan to increase volunteer utilization : Write a 2-3 page marketing plan to increase volunteer utilization from grocery and retail stores in Hillsborough County Florida for nonprofit agency Syliva Thomas Center [www.sylviathomascenter.org]
Obtain force t exerted by the thumb and the force f exerted : A lunch tray is being held in one hand. The mass of the tray itself is 0.200 kg, and its center of gravity is located at its geometrical center. On the tray is a 1.00-kg plate of food and a 0.250-kg cup of coffee. Obtain the force T exerted by the..
Find the magnitude of the total force exerted on the door : A uniform, rectangular door 2.2 m high and 2.4 m wide having a weight of 260 nt is supported by two hinges. One hinge is .30 m from the top corner and the other is .30 m from the bottom corner. Each hinge supports half the total weight of the door..
Find the magnetic field at a distance r from the center : Find the magnetic field at a distance r from the center of a long wire that has radius 3.13 mm and carries a uniform current per unit area 208 A/m^2 in the positive z direction.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Dry air is contained in a tank with fixed volume

Dry air is contained in a tank with fixed volume at 200 degrees Celsius and a pressure of 5 bar. Then the fluid is heated so that its temperature reaches up to 300 degrees Celsius. If the volume of the tank is 0.2 m^3, find the transferred heat and f..

  For the compressor the isentropic efficiency is 92 and for

air enter the compressor of a referative air standard brayton cycle with a volumetric flow rate of 60 m3s at 0.8 bar

  What is the volume capacity of cylinder with stops engaged

0.5 kg of water initially at 400 kPa and 0.3 m3/kg is contained within a piston-cylinder device fitted with retractable stops (initially retracted) so that the water supports the weight of the piston and the force of the atmosphere (state 1). The wat..

  Determine the isentropic efficiency of this turbine

Air is expanded from 1.5MPa and 177°C to 90kPa in an adiabatic turbine. Determine the isentropic efficiency of this turbine if the air is exhausted at 0°C

  Determine a the initial acceleration of the projectile b

a projectile enters a resisting medium a x 0 with a initial velocity of vo 900 fts and travels 4 in. before coming to

  Determine the magnitude or bending stress and shear at

an i beam with flange size 40 mm x 40 mm and a web of 1200mmx 24mm is subjected to a bending moment of 900onm and a

  The portion of the truss shown represents the upper part of

the portion of the truss shown represents the upper part of a power transmission line tower. for the given loading

  Some other heat is also transferred at 200degc calculate

ater enters a reversible steady-state device at 125degc and 400 kpa and leaves at 300degc and 200 kpa. heat is added

  Temperatures of the boiling and condensing sections

Determine the heating rate delivered by the 10 thermosyphons when boiling occurs at 25% of the CHF. What are the mean temperatures of the boiling and condensing sections?

  Find the shaft id needed to obtain a maximum deflection

Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

  What are the minimum value of the magnitude ratio and the

a pressure transducer has a natural frequency of 50 khz and a damping ratio of 0.4. it is to be used to measure

  Determine the heat rate entering the tube

If  the  tube  surface  temperature  at  the  exit  is Ts,o 160°C, determine the heat rate entering  the tube. Evaluate properties at T 400 K.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd