Consider a gas-turbine power plant whose pressure ratio is

Assignment Help Mechanical Engineering
Reference no: EM13628366

Consider a gas-turbine power plant whose pressure ratio is 8. The Isentropic efficiencies of the compressor and the turbine are 80%, and there is a regenerator with effectiveness 0f 70%. When the mass flow rate of air through the compressor is 40 kg/s, the turbine inlet temperature becomes 1700 K. But the turbine inlet temperature is limited to 1500 K, and thus steam injection into the combustion gases is being considered. However, to avoid the complexities associated with steam injection, it is proposed to use excess air (that is, to take in much more air than needed for complete combustion) to lower the combustion and thus turbine inlet temperature while increasing the mass flow rate and thus the power output of the turbine. evaluate the proposal, and compare the thermodynamic performance of "high air flow" (different design values) to that of a "steam injection" gas turbine power plant under the following design constrained conditions:

- The ambient air is at 100 kPa and 25oC.
- Adequate water supply is available at 20oC.
- The amount of fuel supplied to the combustion chamber remains the same.

Reference no: EM13628366

Questions Cloud

A 012-ounce bullet hits at 2000 fts a suspended 10-lb : a 0.12-ounce bullet hits at 2000 fts a suspended 10-lb block of wood and becomed embedded in it. the angle alpha
By what ratio does the momentum of the protons increase the : a electrons are accelerated from rest across 127.75 kv. they are then directed at two slits which are the size of a
The mass of the ball is m2kg and the strings length is l1m : the mass of the ball is m2kg and the strings length is l1m. the ball is released from rest in position 1 and swings to
Compare the energy needed for the first reaction of the : a compare the energy needed for the first reaction of the carbon cycle that for a deuterium tritium reaction.b the
Consider a gas-turbine power plant whose pressure ratio is : consider a gas-turbine power plant whose pressure ratio is 8. the isentropic efficiencies of the compressor and the
Consider the daughter of radon 222 through alpha decay a : consider the daughter of radon 222 through alpha decay. a sample which initially contained 10 moles of this daughter
The uniform slender has a mass of 15 kg determine the : the uniform slender has a mass of 15 kg. determine the horizontal and vertical components of reaction on pin o and the
A 20-m rope is lying on a table you pick up one end and : 1. a 2.0-m rope is lying on a table. you pick up one end and start raising it. how high above the table is the center
In one such experiment a beam of protons is fired with a : 1. in a particel accelerator protons are fired at a stationary target and collide elastically with the nuclei of the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd