User Account

All Pages

Consider a carnot cycle for water in a piston-cylinder

Assignment Help Mechanical Engineering
Reference no: EM13625356

Consider a Carnot cycle for water in a piston-cylinder device. The mass of the water is 1.5 kg. During the isothermal expansion the water is heated from a quality of 0.2 at a pressure of 25 bar to the saturated vapor state. The vapor then expands adiabatically to a pressure of 0.9 bar and a quality of 0.8.
a) Sketch the P-v diagram for this cycle
b) Evaluate the heat and work for each process (kJ)
c) Evaluate the thermal efficiency

Reference no: EM13625356

Questions Cloud

Determine the electrical power that must be supplied to a : a storage tank consists of a cylindrical section that has a length and inner diameter of l2 m and di1 m respectively
Two resistors r1 and r2 are in series with a 78 volts : two resistors r1 and r2 are in series with a 7.8 volts battery. if r1 has a resistance of 2.0 omega and r2 receives
If on striking the ground it embeds itself 700 in into the : an arrow is shot straight up in the air with an initial speed of 210 fts. if on striking the ground it embeds itself
Partition 100 numbers from 0 to 99 according to the : consider the following probability distributiondemand 0 1 2 3 4probability .15 .30 .25 .15 .15partition
Consider a carnot cycle for water in a piston-cylinder : consider a carnot cycle for water in a piston-cylinder device. the mass of the water is 1.5 kg. during the isothermal
What is the greatest distance at which these headlights can : the headlights of a pickup truck are 1.32 m apart.a. what is the greatest distance at which these headlights can be
The jib crane is supported by a pin a c and rod ab the rod : the jib crane is supported by a pin a c and rod ab. the rod can withstand a maximum tension of 40kn. if the load has a
This isnt a specific problem but a question in general when : this isnt a specific problem but a question in general. when is it appropriate to use double integrals in solving for
After it rolls on the horizontal surface for a short : a sphere with a mass of .3 kg and a radius of 15 cm starts from rest on a 22 degree incline 50 cm above a horizontal

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the angular velocity and angular acceleration

Block B of the mechanism is confined to move within the slot member CD. If AB is rotating at a constant rate of AB = 3rad/s, determine the angular velocity and angular acceleration of member CD at the instant shown.

  Clculate a stroke length cm b average piston speed msec c

a pickup truck has a five liter four stroke cycle v6 si engine operating at 2400 rpm. the compression ratio rc10.21 the

  Dtermine the heat transfer per unit width assuming rec

in a chemical processing plant glycerin flows over a 1 m long heated flat plate at free-stream conditions u infinity

  Compute the stress level

For this same component and alloy, compute the stress level at which fracture will occur for a critical internal crack length of 6.0mm.

  After drawing a neat and clear schematic of the geometry

a 5 ft3 tank containing steam at 14.7 psia 1 quality is fitted with a relief valve. heat is transferred to the tank

  Calculate the bulk density of a rock which has 20 porosity

calculate the bulk density of a rock which has 20 porosity. the bulk mineralogy of the rock is 80 quartz 15 calcite and

  Air expands from 100kpa 40 degrees c with volume 75 m3 to

air expands from 100kpa 40 degrees c with volume .75 m3 to 15kpa in a polytropic process with polytropic exponent n.

  Steam at 160 bar 480degc enters a two-stage turbine

steam at 160 bar 480degc enters a two-stage turbine operating at steady sate with a volumetricnbspflow rate of 800

  The discharge temperature is 400 c a heat loss of 10 kw is

a steam compressor is used to increase the pressure of saturated water vapor at 1000 kpa to 1500 kpa. the flow rate is

  It takes an airbus roughly 75 seconds to get to that

an airbus 310a with a mass of 140000 kg sits on a runway. it takes off and flies to an altitude of 10500 m with a speed

  A periodic torque with a maximum value of 10 n-m at a

a periodic torque with a maximum value of 1.0 n-m at a frequency of 5.0 rads is applied to a flywheel suspended from a

  Determine the mass flow rate of condensor cooling water in

water is the working fluid in an ideal rankine cylce. saturated vapors enters the turbine at 16mpa and the condensor

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd