Connect a voltage divider to an output of a dc power supply

Assignment Help Electrical Engineering
Reference no: EM13280920

connect a voltage divider to an output of a DC power supply. Design it to give an output that is 1/3 of the supply voltage. Furthermore neither the power ratings of the resistors nor the current rating of the supply are to be exceeded. The voltage output of the divider much not change by more than 1% when loaded with 10killohom.

Reference no: EM13280920

Questions Cloud

Determine the first sphere hits the ground at a distance : Two small spheres having same mass and charge are loacated at the same vertical line at heights h1 and h2(h2>h1). They both are thrown simultaneously with the same velocity V in the same direction along the horizontal.
What is the amount of the lump sum : What is the amount of the lump sum that would be exactly equal to the present value of the annual installments? Round off to the nearest $1.
Find the magnitude of the force of the dog on elevator floor : a 5.0 kg dog sits on the floor of an elevator that is accelerating downward at 1.20 m/s^2 , find the magnitude of the force of the dog on the elevator floor
What will the investment be worth at the end : If you place $50 in a savings account with an interest rate of 7% compounded weekly, what will the investment be worth at the end of five years (round to the nearest dollar)?
Connect a voltage divider to an output of a dc power supply : Design it to give an output that is 1/3 of the supply voltage. Furthermore neither the power ratings of the resistors nor the current rating of the supply are to be exceeded. The voltage output of the divider much not change by more than 1% when l..
What is your holding period return : You bought Chemtron stock for $45 a year ago. It is selling for $54 today. What is your holding period return?
Demonstrate that system model work by running inputs : Pattern Recognizer (using a state transition diagram in simulink) Consider a Pattern Recognizer that accepts single digit inputs (0-9) each time unit and outputs a NO (or 0) until the pattern 933493 has been seen in the stream of inputs
What is the circumference and radius of planet : A planet Z has a hole bored in it at its equator , and a shaft of light from it's star goes straight down that hole to the bottom, what is the circumference and radius of planet Z
What is determination of proportions of various securities : What is the determination of the proportions of various securities within a portfolio referred to as?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Convert the value entered in r3 from hexadecimal to ascii

Students should type up, assemble and emulate the BIN2ASCII program which converts the value entered in R3 from Hexadecimal to ASCII. This should be done by dividing R3 by 10 (decimal) and converting the remainder to ASCII

  What is the load resistance in ohms as measured

A 5-MVA, 66:13.2kV, three-phase transformer supplies a three-phase resistive load of 4,500kW at 13.2kV. What is the load resistance in ohms as measured from the line-to-neutral on the high-voltage side of the transformer, if it is connected in Y-Y..

  What is the maximum value of n0 for an fm cell phone

What is the maximum value of N0 for an FM cell phone whereby ST=

  Find the critical path and determine the propagation delay

Design the combinational 3 bit gray to binary code converter for conversion angular position of a shaft into binary code. 1) Complete the truth table 2)obtain the minimal solution with a K map 3) draw the circuit diagram, labels the inputs and output..

  Describe a system for removing the sharp transitions

In a digital audio system, a digital to analog converter reproduces the analog voltage levels represented by the digital samples. This signal is inherently jagged with sharp transitions between each sample.

  Research the recent history of gasoline pricing

Research the recent history of gasoline pricing in your area, and attempt to relate any fluctuations you observe to documented supply and demand factors outlined in our book. Be sure to cite any references used.

  How long after sudden dark-to-light flash before cell output

A photocell with a 35-ms time constant is used to measure light flashes. How long after a sudden dark-to-light flash before the cell output is 80% of the final level

  Explain can three of the doublers be interconnected

a) Design the doubler circuit shown in Figure 2, for which:D = d8 d4 d2 d1 and B = b8 b4 b2 b1  are each an 8421 BCD code digit. The circuit must implement the equation: 10C* + B = 2D + C

  Define multiplexer with an active low enable

(c) Use a single 4-to-1 multiplexer with an active low enable and an active high output and a minimum of additional gates. Show the function expansion both algebraically and on a Karnaugh map.

  Describe the difference between a n-channel and a p-channel

Describe the difference between a N-Channel and a P-Channel CMOS transistor when a signal is applied to the gate

  Calculate equation of a line that is tangent to function x

Write a script that numerically calculates the slopes for the function y = ex. Use x-values that range from 0 to 10 in increments of 0.1. Using these slopes, calculate the equation of a line that is tangent to the function at x = 8.3.

  Find how many numbers are above the average

1- Write a function that shows you how to calculate F(x) = 0.1X^2+5Y^3 2- Read and write a File that has a set of 10 numbers. Then assign those numbers to an array.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd