Computing temperature water evaporation

Assignment Help Mechanical Engineering
Reference no: EM13138163

Calculating temperature, water evaporation, and heat in a power plant cooling situation.
In a nuclear power plant the cooling tower system must be run on a closed cycle. That is, the air exiting the tower passes over cooling coils to return it to its initial condition prior to reentering the tower. Air at 20 degrees C and 40% relative humidity enters the tower at a rate of 1.3 x 106 kg/sec. Water enters the tower at 50C and leaves at 25C. The water flow rate is 750,000 kg/sec. Saturated air exists the tower and passes over cooling coils which returns it to 20C and 40% relative humidity. Water at 22C condenses out of the air. Determine:

A) The temperature of air leaving the tower
B) Amount of water evaporating in kg/sec.
C) The heat removed by the cooling coils in kW

Reference no: EM13138163

Questions Cloud

What would be the necessary journal entry : On December 31, 2007, Drew Company issued $170,000, five-year bonds for $155,000. The stated rate of interest was 6 percent and interest is paid annually on December 31. What would be the necessary journal entry?
Financial leverage characteristic of long-term debt : The financial leverage characteristic of long-term debt results in:
Find out the exit temperature : Determining the Exit Temperature and Power Input of Air through a Compressor, Air at 150Pa and 310K enters a compressor of inlet diameter 2cm. The Compressor raises the pressure to 3.5 times the inlet pressure
Enty to record depreciation expense : on january 1, 2011, Sesame revised these estimates to a total useful life of 4 years and a salvage value of $10,000. Prepare Sesame's enty to record 2011 depreciation expense.
Computing temperature water evaporation : Calculating temperature, water evaporation, and heat in a power plant cooling situation. In a nuclear power plant the cooling tower system must be run on a closed cycle.
Interest costs throughout construction : The contractor was paid $2,200,000. An assessment made by the city for pavement was $6,400. Interest costs during construction were $170,000.
Define two infinite parallel plates are separated : Two infinite parallel plates are separated by a distance h. The space between them is filled with a Newtonian fluid: density (rho), viscosity (mu). The lower plate is fixed
Explain a large stationary brayton cycle gas-turbine : A large stationary Brayton cycle gas-turbine power plant delivers a power output of 100MW to an electric generator. The minimum temperature in the cycle is 300K
Concept of allowance for doubtful accounts : Determine the amount to be added to Allowance for Doubtful accounts in each of the following cases. (a) Balance of $500 in the allowance account just prior to adjustment. Analysis of accounts receivable indicates doubtful accounts of $9,500.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd