Computer the volume of fill that will be produced

Assignment Help Civil Engineering
Reference no: EM13555104

A 3 ft deep cut is to be made across an entire 2.5-acre site. The average unit weight of this soil is 118 lb/ft^3, and the average moisture content is 9.6%. It also has a maximum dry unit weight of 122 lb/ft^3 and an optimum moisture content of 11.1%, based on the modified Proctor test. The excavated soil will be placed on a nearby site and compacted to an average relative compaction of 93%. Computer the volume of fill that will be produced and express your answer in cubic yards.

Reference no: EM13555104

Questions Cloud

What is the shear strength in terms of effective stress : What is the shear strength in terms of effective stress on a place within a saturated soil mass at a point where the total normal stress is 295 kN/m2^2 and the pore water pressure 120 kN/m^2?
What is the average number of vehicles waiting to be served : An expressway off-ramp consisting of a single lane leads directly to a tollbooth. The rate of arrival of vehicles at the expressway can be considered to be Poisson with a mean of 30 veh/h.
Determine two possible angles theta at which this : A fireman is standing on a hoist and sprays water at a fire. the fire is 35 ft in the x direction and 20ft downward in the y direction. the water flows at 65 ft/s. determine two possible angles theta at which this can be done. assume the angle below ..
Find steady state concentration of pollatant in the lake : A lake with constant volume 10x10^6 m^3 is fed by pollation free stream with flow rate 50m^3/s. fator dumps 5m^3/s of nonconservative waste with concentration
Computer the volume of fill that will be produced : A 3 ft deep cut is to be made across an entire 2.5-acre site. The average unit weight of this soil is 118 lb/ft^3, and the average moisture content is 9.6%.
Determine the magnitude of the reaction force exerted at b : The image is of a plane who's wheels are spread apart by 12 ft and on the ground. The left wheel being point A and the right wheel being point B. It also has an arrow around the front propeller in the clockwise direction.
What it the distance after adjusting for sag : A 200ft tape is hung in catenary. It is supported at the 80ft mark the tension is 20lbf and the weight of the tape is 3 lbf 5 0z. The measured distance is 187.01 what it the distance after adjusting for sag?
What will be the concentration of tce in the aqueous phase : The dimensionless henry's constant for TCE at 25 degrees celsius is 0.4. A sealed glass vial is prepared that has an air volum of 4mL overlying an aquesous volume of 36mL. TCE is added to the aqueous phase so that initally
Determine which driver will be the first to displace later : Vehicles A and B are traveling toward each other in the opposing lanes on a straight segment of a two-lane highway at 35 and 40 mph respectively. If the critical rates of angular change of the two drivers are 0.0065 and 0.0055 rad/s, determine

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the predicted number of zebra mussels years from now

The zebra mussels have a net growth rate of 0.09 yr-1. At the current time there are 176 zebra mussels in the stream. What is the predicted number of zebra mussels 5, 10, and 20 years from now

  Determine the design load for strength and service ability

Determine the design load for strength and serviceability limit states (short-term and long term), for a steel beam in a residential building with the following data;

  Determine what is the displacement from t

Suppose that the acceleration of the train during the interval time from t=2 to t=4 s is a 2t m/s^2, and at t = 2 s its velocity is v = 180 km/hr. What is the train's velocity at t = 4 s

  How long does it take to reach an altitude of 3000m

Missiles designed for defense against ballistic missiles haveattained accelerations in excess of 100g's or 100 times theacceleration due to gravity. Suppose that the missile

  What torque is required to drive the disk at 660 rpm

A disk spins within an oil-filled enclosure, having 2.4 mm clearance from flat surfaces each side of the disk. The disk surface extends from radius 12 to 86 mm.

  Determine the elastic modulus of the composite material

An SAE steel wire (1mm diameter) is coated with another cover to form a composite material with diameter of 2 mm. a) determine the elastic modulus of the composite material;

  Define data mining confusion matrix

Suppose that you issued a query against a search engine and the search engine retrieved 125 documents. Suppose that there are total, Define Data mining confusion matrix

  Find the point where the normal reaction n acts on the block

a block of mass m is on an inclined plane that makes angle from the horizontal plane. the coefficient of friction between the plane and the block is µ. find the point where the normal reaction N acts on the block.

  Determine the maximum internal pressure in mpa

The rivets are 10 mm in diameter, spaced a distance s = 24.4 mm apart, and have an average shear strength of 35 MPa. Determine the maximum internal pressure in MPa if the rivets are not to shear.

  Determine the entrance losses

A 40 cm diameter well has been constructed in a water-table aquifer. A pump capable of continuous discharge at 600 m3/day has been installed to test the well. Observation wells are located 10 meter and 50 meters from the pumped well. After pumping co..

  What are the key aspects of the drawing you need to check

As a design engineer you are responsible for all the drawing documentation from your organisation. What are the key aspects of the drawing you need to check before sending it to the construction division?

  Find what are the monthly payments and the total interest

A 2014 Ford Mustand convertible in 'Gotta have it Green Metallic' is retailing for $38,000. If you put $3,500 down on the vehicle, and obtain approval for a 2.19% car loan compounded monthly for 5 years.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd