Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
a digital signal represented by a binary voltage +5.55 and -4.5V , is transmitted over an AWGN channel with noise standard dev 1.12 V.Compute the volt. f the optimum thresholdwhen the priori probabilities of the binary source are a follows
i) P(0) = 0.4ii) P(1) = 0.25iii) P(0) = 0.5
A closed-loop system has a hold circuit and process as shown below. Determine G(z) when T = 1 and Gp(s) = 2 / (s + 2). A sampled-data system such as that presented in the above problem has a sampling period T = 0.05s
What value of emitter resistor would you choose, if: a) You have to amplify the signal of a microphone that has an internal resistance of 100K using a Common Emitter bias configuration b) you have to drive a load of 50 with an Emitter Follower cir..
In this project we will consider the control of a synchronous generator supplying electricity to the grid.
A full-wave bridge rectifier circuit with a 1-kohms load operates from a 120-V (rms) 60-Hz household supply through a 10-to-1 step-down transformer having a single secondary winding
If we wish to design a communication system which carries voice securely, we need to ensure that others cannot tap into the conversation. In digital transmissions, we can do this by encryption.
A square wave signal with voltage levels 0 volts and 2.0 volt at a frequency of 1.00 MHz is multiplied by a sine wave at a frequency of 5.0 MHz
1. Sketch the polar plot of the frequency response for the following loop transfer functions: Gc(s)G(s) = 1 / ((1 + 0.25s)(1 + 3s)) Gc(s)G(s) = 5(s^2 + 1.4s + 1) / (s - 1)^2 Gc(s)G(s) = (s - 8) / (s^2 + 6s + 8) Gc(s)G(s) = 20(s + 8) / (s(s +2)(s + 2)..
A CMOS output driver circuit on an IC is connected to an external transmission line. The NMOS and PMOS transistors have gate oxide thickness d = 2.0 nm and channel length L = 0.25 mum. The power rail is VDO = 1.0 V.
You want to download a 5 Mbit file over a 10-Mbps Rayleigh fading channel in the 1800 MHz frequency band. You are traveling at 6 km/h and use 1000-bit packets.
A Y-connected load has an impedance of 25+j12 ohms in each phase. It is desired to raise the load power factor to .95 lagging. (a) What size capacitor should be placed in parallel with each phase impedance if frequence = 60 Hz
A constant electric field, E=12 V/cm, exists in the +x direction of an n-type gallium arsenide semiconductor for . The total current density is constant and is equal to 100 A/cm2. At x=0, the drift and diffusion current densities are equal.
The frequency response of an FIR filter is H(ejw)=b0+b1*e^-jw+b2*e^-2jw. In each case below, state whether the filter is highpass, lowpass, bandpass or band stop and draw the pole zero plot.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd