Compute the vertical deflection and slope of cantilever beam

Assignment Help Mechanical Engineering
Reference no: EM131513595

Question: 1. Compute the deflection at midspan and the slope at A in Figure P8.19. EI is constant. Express the slope in degrees and the deflection in inches. Assume a pin support at A and a roller at D. E = 29,000 kips/in.2, I = 2000 in.4.

2023_8.19.png

2. (a) Compute the vertical deflection and slope of the cantilever beam at points B and C in Figure P8.20. Given: EI is constant throughout, L = 12 ft, and E = 4000 kips/in.2. What is the minimum required value of I if the deflection of point C is not to exceed 0.4 in.?

1645_8.20.png

Reference no: EM131513595

Questions Cloud

Evaluate the salespersons tactics : Evaluate the salespersons tactics using the material you have learned this quarter. You should begin by expression interest in the product.
Compute the vertical displacement of the hinge : Compute the vertical displacement of the hinge at C for the funicular loading shown in Figure. The funicular loading produces direct stress on all sections.
Long-term asset acquisition : Roxy and Harley (R & H) is considering a significant equipment replacement. At this point the equipment is depreciated to its salvage value.
What is the deflection define briefly : Determine the horizontal and vertical deflection of the hinge at point C of the arch in Figure P8.16 for a single concentrated load of 60 kips applied at joint.
Compute the vertical deflection and slope of cantilever beam : Compute the deflection at midspan and the slope at A in Figure P8.19. EI is constant. Express the slope in degrees and the deflection in inches.
Firm approximate weighted average cost of capital : what is the firm’s approximate weighted average cost of capital?
Compare the deflection at b with the deflection at midspan : Derive the equations for slope and deflection for the beam in Figure P7.1. Compare the deflection at B with the deflection at midspan.
Sales using regression to estimate a trend : What would be the forecast for next year's sales using regression to estimate a trend?
What will be the firms cash cycle : Assuming that all of Freddie's sales are on credit, what will be the firm's cash cycle?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The system contains a sharp-edged

a liquid at 10 c kinematic viscosity of 1.30710-6 m2s is to flow from a roof-top reservoir to a tanker truck through a

  The remaining steam continues expansion with an isentropic

in a steam power plant which utilizes rankine cycle steam enters the turbine at 100 bar and 400oc. it expands with an

  A steel pipe of 12-in outer diameter is fabricated from

a steel pipe of 12-in. outer diameter is fabricated from 14in. thick plate by welding along a helix which forms an

  Find the total transverse te waves in a waveguide

Find the total transverse TE waves in a waveguide of width a and height b if a forward-propagating wave of amplitude Ho and a backward-propagating wave of amplitude H1 exist.

  Find the maximum altitude

Find the maximum altitude h which the cone may have before the object will no longer float in the upright position illustrated.

  1 write a program that takes the image tracksjpg and finds

1 write a program that takes the image tracks.jpg and finds canny edges and then finds lines in these edges using the

  What is the energy efficiency of converting cow manure

What is the energy efficiency of converting cow manure to biogas if it yields 25 m3 per Mg with the methane content of 55% (35 MJ/m3)?

  If the surface of the tower is normally kept at 23 celcius

a 70 meter tall cylindrical tower with outer diameter 12 meters is exposed to a very cold evening where the temperature

  A brayton cycle produces 14 mw with an inlet state of 17oc

a brayton cycle produces 14 mw with an inlet state of 17oc 100 kpa and a compression ratio of 161. the heat added in

  Define the interactive role of the owner

Describe the differences between project objectives and project scope definition. Define the interactive role of the owner and designer in this process to ensure a well-defined understanding between the two parties.

  Determine the resulting force created by the vehicle and

a construction vehicle of mass 30 mg is used to unload sand in a horizontal line through a port on the bottom of the

  Explore the effect of variations in the flow velocity

Explore the effect of variations in the flow velocity and electrical current on the surface and centerline temperatures of the wire.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd