Compute the spring rate and the solid height

Assignment Help Mechanical Engineering
Reference no: EM131377790

A helical compression spring used for essentially static loading has d = 0.100 in., D = 0.625 in., N = 8, and squared and ground ends. It is made of ASTM A227 cold-drawn steel wire.

(a) Compute the spring rate and the solid height.

(b) Estimate the greatest load that can be applied without causing long-term permanent set in excess of 2 percent.

(c) At what spring free length will the load determined in part (b) cause the spring to become solid?

Reference no: EM131377790

Questions Cloud

Can ralph rescind his promise : Ralph, knowing that his son, Ed, desires to purchase a tract of land, promises to give him the $25,000 he needs for the purchase. Ed, relying on this promise, buys an option on the tract of land. Can Ralph rescind his promise?
Provide the result in given situation : Ann paid $150 and stated to Barry that all claims had been paid in full. In August 2008, Barry demanded the unpaid balance and subsequently sued Ann for $350. Result?
List the common spring materials presented : Which materials are listed as highly susceptible to hydrogen embrittlement?
Is there a contract between joyce and hill : On May 18, Hill, known to Joyce, sold the house to Gray, who was ignorant of the unrecorded option. On May 20, Joyce sent an acceptance to Hill who received it on May 25. Is there a contract between Joyce and Hill? Explain.
Compute the spring rate and the solid height : A helical compression spring used for essentially static loading has d = 0.100 in., D = 0.625 in., N = 8, and squared and ground ends. It is made of ASTM A227 cold-drawn steel wire.
Who should prevail in given situation : Subsequently, Great American sued Berryessa on the note. He defends against the note on the grounds of duress and counterclaims for the return of the $1,500 and the cancellation of the uncashed $500 check. Who should prevail?
How would you reach your target markets : If you were in Amilya Antonetti's place starting SoapWorks, what marketing strategy would you use to compete with Procter & Gamble and Clorox? How would you reach your target markets? How and where would you advertise? How would you use "word of m..
What will johnson need to show in order to prove his cause : He then alleged, among other claims, that IBM subjected him to economic duress when he signed the release and covenant-not-to-sue, and he sought to rescind both. What will Johnson need to show in order to prove his cause of action?
Estimate the maximum static load that can be applied : A helical compression spring is to be made with a wire diameter of 2 mm, an outside diameter of 19 mm, ten active coils, and ends closed and ground. The least expensive steel spring wire is to be used, and presetting will not be used.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd