Compute the maximum speed of train

Assignment Help Electrical Engineering
Reference no: EM131415036

a sub urban train runs with an average speed of 36km/hr between two stages 2km apart .values of acceleration and retardation are 1.8 km/h/s and 3.6km/h/s. compute the maximum speed of train assuming trapezoidal speed time curve.

Reference no: EM131415036

Questions Cloud

Estimate the external gas-to-particle mass-transfer : At a location in the bed where the pressure is 653.3kPa, the temperature is 21°C, the gas flow rate is 1.327 kg/min, and the dew-point temperature is 11.2oC, estimate the external, gas-to-particle mass-transfer and heat-transfer coefficients.
Write a batch file which creates and populates a database : You must write a batch file which creates and populates a database of between 4 and 6 tables. The database must be of your own making and should be of an area of interest to you or related to your work
Ethics based on nature and purpose of the consent : Q1. What is the difference between law and Ethics based on nature and purpose of the consent, Illustrate with an example? Why informed consent is important in medical ethics? (Ref; Chapter 2)
What is the primary source of structured data : Why does the data-information-knowledge continuum depend on structured data? What is the primary source of structured data? In what component of the EHR is structured data processed to provide information? In what component of the EHR is information ..
Compute the maximum speed of train : a sub urban train runs with an average speed of 36km/hr between two stages 2km apart .values of acceleration and retardation are 1.8 km/h/s and 3.6km/h/s. compute the maximum speed of train assuming trapezoidal speed time curve.
Key issues of the cases : Whirlpool's experience in China: What are the lessons learned? What are the new challenges when sourcing globally?
What is the main ingredient in street meth : What is the main ingredient in street meth? Where is "ingredient" it made? What is the DEA doing to slow down production of street meth?
Explain the political impact of this womens health issue : As an advanced practice nurse, you must remain current on health issues that commonly impact women such as birth control, abortion, family planning, the human papillomavirus (HPV) vaccine, and human immunodeficiency virus (HIV). Many of these wome..
Calculate the belt pass frequency for a belt drive : A signal is sampled at 100 samples/sec. It was later found that the original signal contained a frequency component at 60 Hz. Calculate the frequency at which the aliasing effect is seen in the power spectrum in the frequency range [0 50] Hz.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What degree of matching in emitter area is required

What degree of matching in emitter area is required for the base-emitter voltages of two bipolar devices with identical collector currents to have a difference of less than 5.0mV. Use VT= 25.85mV.

  Write an expression for the modulated signal sfm

An analog AMPS cell phone channel at 900MHz carrier has a carrier amplitude of 4V and is a modulation signal m(t)=Bmsin(10000*pi*t). The amplitude of the modulating signal is 2V and the peak frequency deviation was found to be 10kHz

  A student decides to have a little fun and designs an rtd

a student decides to have a little fun and designs an rtd with the pattern shown below. if the rtd is made of ni with

  Find out the input voltage range

For a given zener diode circuit, find out the input voltage range

  Find the radii a and b of the inner and outer circles

Determine the average transmitter powers for the two signal constellations, and compare the two powers. What is the relative power advantage of one constellation over the other? (Assume that all signal points are equally probable.)

  Design logic to turn on indoor light if it is dark outside

The light sensor, which is active when it is dark, monitors the outdoor light and the timer can be programmed to any time. Design the logic to turn on an indoor light if it is dark outside and the timer has set the enable. A high turns on the ligh..

  What should always be checked when replacing an overload

A technician reads 240 V across the thermal overload to the first strip heater on an electric furnace. What does this mean?

  Determine the turns ratio for the transformer

The amplifier has a Thévenin voltage of 25[Vrms], and a Thévenin resistance of 0.275[O]. Find the turns ratio for the transformer, so that the maximum possible power is delivered to the speaker.

  What must the load be to extract maximum power from circuit

Consider a circuit that is connected to a phasor of 120V/0 degrees. The circuit feeds a 10 ohm resistor on the "hot" lead and then the circuit branches. One branch has a 0.1 A /-300 degree phasor current source (oriented with "arrow oriented right..

  Find the overall noise figure of the system

find the overall noise figure of the system.

  Why must an e-mosfet be handled with care

Why would a designer generally select a MOSFET over a BJT for a power-switching function in a switching power supply?

  Determine what is the induced emf in the armature

A 12-kW, 120-V dc series generator has a series field resistance of 0.05 Ω. The generaated emf is 135V when the generator delivers the rated load at its rated terminal voltage. What is the armature resistance

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd