Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1. A 6.4 mm (0.25 in.) diameter cylindrical rod fabricated from a 2014-T6 aluminum alloy (Figure 8.34) is subjected to reversed tension- compression load cycling along its axis. If the maximum tensile and compressive loads are +5340 N (+1200 lbf) and -5340 N (-1200 lbf), respectively, determine its fatigue life.Assume that the stress plotted in Figure 8.34 is stress amplitude.
2. A 15.2 mm (0.60 in.) diameter cylindrical rod fabricated from a 2014-T6 aluminum alloy (Figure 8.34) is subjected to a repeated tension- compression load cycling along its axis. Compute the maximum and minimum loads that will be applied to yield a fatigue life of 1.0 X 108 cycles. Assume that the stress plotted on the vertical axis is stress amplitude, and
(a) Make an S-N plot (stress amplitude versus logarithm cycles to failure) using these data.
(b) Determine the fatigue strength at 4 X 106 cycles.
(c) Determine the fatigue life for 120 MPa.
gasoline at 20 degrees centigrade flows through a 6-cm-diameter pipe. it is metered by a modern venturi nozzle with d4
pneumatic nail driver uses .02 ft3 of air at 100 psia and 1 btu of energy per nail must drive 500 nails with a tank no
Consider a cold air-standard Diesel cycle. At the beginning of the compression process, the pressure is 0.1 MPa, the temperature is 320 K, and the volume of air is 0.02 m3. The maximum temperature of the cycle is 1500 K, and the compression ratio is ..
car a is traveling at va130kmh as it passes a police officer in car p but over the next 5 seconds the car uniformly
for a newtonian fluid or a power law fluid flowing through a cylindrical tube of radius r calculate the constant k in
Superheated steam at 600 C and 4000 kPa is fed into a turbo expander at a rate of 10 kg/s. The steam expands and leaves the expander at 500 kPa pressure and 300 C. It is known that there is a heat loss of 50 kJ/sec. This heat loss can be assumed to t..
Outside air at 1 bar, 5 °C and RH 70% is heated to 25 °C. The flow rate of air is 50 m 3/min. Find (a) the final relative humidity, (b) the rate of heat transfer (in kW) needed to heat up the air?
a food department is kept at -15 degrees celsius by a refrigerator in an environment at 25 degrees celsius. the total
In order to double check your speedometer on your boat you decide to install a pitot tube on the bottom. One tube protrudes straight downward, while the other tube has a 90 degree bend, pointing the tip into the direction of motion. At rest, the wate..
Find the temperature of water at 200 kPa and specific enthalpy of 350 kJ/kg. A heat pump and a refrigerator operate on same cycle between same hot and cool reservoir at temperature TH, and TL, respectively. Please demonstrate = +1 COPHP COPRF and com..
lf the 50-kg crate starts from rest and achieves a velocity of v 4 ms when it travels a distance of 5 m to the right
In a particular fission event, a thermal neutron produces fission of a U-235 atom. For this particular event, the fission products Br-90 and Xe-143 are produced as well as 3 neutrons. How much energy in MeV is produced from this event?
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd