Compute the max horizontal shear stress at the neutral axis

Assignment Help Civil Engineering
Reference no: EM13319431

A solid rectangular simply supported timber beam 6 in wide, 20 in deep, and 10 ft long carries a concentrated load of 16,000 lb at midspan. Use nominal dimensions.

a.) Compute the maximum horizontal shear stress at the neutral axis.

b.) Compute the shear stress 4 in and 8 in above and below the neutral axis. Neglect the weight of the beam

Reference no: EM13319431

Questions Cloud

The firm is proposing to buy a new plant which can generate : The firm is proposing to buy a new plant which can generate additional annual profit of Rs. 10,000. The fixed costs of new plant is expected to Rs. 4000. The new plant will increase the sales volume by Rs. 40,000. It can be assumed that the ratio bet..
Explain what is the final ph of the solution : What is the final pH of the solution when 15.0 mL of 0.121 mol/L NaOH(aq) and 35.0 mL of 0.181 mol/L HNO2(aq) are mixed? Assume the temperature is 25oC.
Estimate settlement of footing four years after construction : The modulus of elasticity of the sand was determined to be 10,000 kN/m^3 throughout. Using the Schmertmann's method, estimate the settlement of the footing four years after construction, using four 1 meter thick sublayers.
Explain the ph of a 0.175 mol/l solution of sodium acetate : What is the pH of a 0.175 mol/L solution of sodium acetate, CH3COONa, at 25oC? (pKa=4.74 at 25oC for CH3COOH.) Give your answer accurate to two decimal places
Compute the max horizontal shear stress at the neutral axis : A solid rectangular simply supported timber beam 6 in wide, 20 in deep, and 10 ft long carries a concentrated load of 16,000 lb at midspan. Use nominal dimensions.
How does monetary policy affect a company financial status : The Fed has three main mechanisms to affect the economy through the money supply and interest rates: open market operations, the discount rate, and reserve requirments. In this assignment, you will write about how these tools can affect a company's f..
What is the final temperature of the rock-water system : If the rock falls from the cliff into a pool containing 7.00m3 of water at 16.3%u2218C, what is the final temperature of the rock-water system
What is the size of basins assuming equal size dimensions : Assuming that the minimum detention time ( with one train out of service) is 30 s, what is the size of these basins assuming equal size and cubic wetted dimension
Evaluate an organization''s strategic business units : 1. To evaluate an organization's Strategic Business Units (SBU), the Boston Consulting Group developed a portfolio performance framework.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Principle of lateral continuity

Would you expect to find the Tapeats Sandstone on top of the Great Unconformity in all places in the Grand Canyon? Why, or why not?

  Determine the max rimpull of the tractor in each gear

A pneumatic-tired tractor with a 354 - hp engine has a maximum speed of 3.6 mph in 1st gear. Determine the max. rimpull of the tractor in each gear if the engine effieicency is 91%.

  Determine peak discharge if unit hydrograph is triangular

A hydrograph has a uniform rainfall intensity of 1.5 in/hr in the first hour, 2.0 in/hr in the second, and 0.75 in/hr in the third hour. Direct runoff (in inches) using the SCS method is 1.2in.

  Determine the value of the dynamic viscosity at conditions

Start from the values for the density and the kinematic viscosity of CO2 at 15o C and standard atmospheric pressure (101.3 kPa), and first determine the value of the dynamic viscosity at the same conditions.

  Determine the specific weight of wood above water surface

a solid wooden cube (.5*.5*.5 m^3) is floating in water and 0.2 of the cube extends above the water surface. Determine the specific weight of the wood.

  Horizontal distance between the points

A runs slope a distance of 156.777 m from one point to another point at a rate of +1.5%. What is the corresponding horizontal distance between the points?

  Determine the design speed and length of the curve

A horizontal curve is designed for a two-lane road in a mountainous terrain. The following data are known: Deflection angle: 40 degrees Tangent: 436.76 Station of PC: 2695 + 73.89 Side friction factor = 0.12 Superelevation = 8% Superelevation run-off..

  Explain why a secant touches a circle at one point

1. The three isometric axes are: vertical and two axes 30 degrees from horizontal. 2. Oblique projection is a perspective projection method. 3. Isometric view represents a parallel projection method.

  How much the person must sell the bond for 6 years

The bond has a maturity date of 10 years from now. How much the person must sell the bond for 6 years from now in order to make a rate of return of 10% per year, compounded semiannually is closest.

  Determine torque that the titanium alloy shaft can transmit

Determine the torque that the Titanium Alloy shaft can transmit if the allowable angle of twist is 0.375 RAD. Assume the torque is applied at the end of the shaft. The shaft is 2 meters long and has a diameter of 25 mm.

  Calculate how much bod is remaining after 12 days

A 250 cubic meter reaction tank contains a waste water having an ultimate BOD concentration of 755 mg/L. If the BOD reaction rate constant is -0.352/day, how much BOD is remaining after 12.0 days

  How far apart in nautical miles are ships at the time

ship A leaves port sailing in a direction 60 degree C north of due east and sails for 12 hours at 10 knot . Sheep B leaves the same port 3 hours later and sails due east at 25 knot for 9 hours.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd