Compute the max acceptable tensile service load for angle

Assignment Help Civil Engineering
Reference no: EM13303617

Compute the maximum acceptable tensile service load for a single L6x4x3/4 angle. The service live load is three times the dead load. The 4-in leg contains a single line of 7/8 inch diameter bolts, and the 6 inch leg contains a double gage line of 7/8 inch diameter bolts. Assume no stagger in the bolts, and that all bolts participate in carrying the load (i.e., both elements are connected).

Reference no: EM13303617

Questions Cloud

How accurately would each 100-ft distance have to be measure : How accurately would each 100-ft distance have to be measured so that the 95% error would no exceeded +-0.24ft in a total distance of 4000ft
Compute the distance when the traffic signal turns red : A driver with his passenger vehicle is driving at 35 mph, when the traffic signal in front of him changes to yellow. He is 100 feet from the intersection when he applies the brakes after a 1-second reaction time.
Calculate the separation distance of the wires : Two long parallel wires carry currents of 2.71 A and 5.93 A. Find the separation distance of the wires
Find how many turns does this solenoid contain : A current of 7.87 A in a solenoid of length 12.0 cm creates a 0.357-T magnetic field at the center of the solenoid
Compute the max acceptable tensile service load for angle : The service live load is three times the dead load. The 4-in leg contains a single line of 7/8 inch diameter bolts, and the 6 inch leg contains a double gage line of 7/8 inch diameter bolts.
Determine the amount of merchandise inventory lost : Complete the Balance Sheet using the information on the Post Closing Trial Balance and determine the amount of Merchandise Inventory lost and prepare the entry to write off the lose.
Find the root-mean-square speed of brownian motion : Smoke particles in the air typically have masses of the order of 10^-16 kg. Find the root-mean-square speed of Brownian motion for a particle with a mass of 3.00 x 10^-16kg in air at 300K
Determine the service rate for six vehicles per minute : Vehicles begin to arrive at a toll booth at eight vehicles per minute from 9 A.M. to 10 A.M. The booth opens at 9:10 A.M. and services at a rate of ten vehicles per minute until 9:40 A.M. From 9:40 A.M. until 10 A.M.
Compute the magnitude of the torque on the tre : Compute the magnitude of the torque on the tree due to the tension in the rope, with the base of the tree acting as the reference point

Reviews

Write a Review

Civil Engineering Questions & Answers

  Find the force

Two smooth circular cylinders of weight w=500N and radius r=200mm are connected at their centres by a string AB of length 600mm and rest upon a horizontal plane.

  Determine purchasing power 3 years from now of an investment

Determine the purchasing power 3 years from now of an investment of $20,000 today. The investment is earning a market interest rate of 8%, and the inflation rate is 3%.

  How to design a horizontal curve for a two-lane road

design a horizontal curve for a two-lane road. The road has 12-ft. lanes. Due to expansive excavation, it is determined that a maximum of 34 ft. can be cleared from the road's centerline toward the inside lane to provide for stopping sight distanc..

  What fraction of the load p is transmitted by the middle bar

The two outer bars (material A) are identical. The cross- sectional area of the middle bar (material B) is 31.544% larger than the cross- sectional area of one of the outer bars. Also, the modulus of elasticity of material A is twice that of mater..

  Shape of a circular arc

Rod AB is bent into the shape of a circular arc and is lodged between two pegs D and E. It supports a load P at end B. Neglecting friction and the weight of the rod, determine the distance c corresponding to equilibrium when a = 43mm and R = 143mm..

  Determine what is angular error if the distance to the pole

A 6-ft range pole is set over a station on which a sight is to be made with a the odolite. If the sight is made to the center of the rod 4-ft up from the ground, and the center of the top of the pole is out of plumb 0.12 feet in a direction normal..

  Determine the velocity v2 of the particle

The motion occurs in the horizontal x-y plane. Determine the velocity V2 of the particle at the end of the 3-s interval.

  At what rate is the diameter increasing after 5 min

A balloon is being inflated at the rate of 15m^3/min. At what rate is the diameter increasing after 5 min? Assume that the diameter is zero at time zero.

  Determine the required value of the mass

a 1 meter diameter cylindrical mass is connected to a 2 meter wide rectangular gate. the gate is to open when the water level drops below 2.5 meters. Determine the required value of the mass of the cylinder in kgs.

  Calculate the maximum length

The elevation of the lowest bottom of the structure is at 1470 feet. Calculate the maximum length (feet) of the parabolic curve required to meet the given conditions.

  Drawing the shearing force diagram

Draw the shearing force diagram and the moment diagram of the following problem. The beam is indeterminate. You need to integrate the moment twice to get a formula for the deflection v(x).

  Detremine the cfat in year 0 for the challenger and defender

The defender had a first cost of $300,000, but its market value now is only $100,000. It has chargeable expenses of $120,000 per year and no expected salvage value. To simplify calculations, assume that SL depreciation was charged at $60,000 per y..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd