Compute the distance when the traffic signal turns red

Assignment Help Civil Engineering
Reference no: EM13303620

A driver with his passenger vehicle is driving at 35 mph, when the traffic signal in front of him changes to yellow. He is 100 feet from the intersection when he applies the brakes after a 1-second reaction time. The vehicle's deceleration rate is 15 ft/sec?^2. If the yellow light is 4 seconds long, compute the distance (feet) where the vehicle will be relative to the intersection when the traffic signal turns red.

Reference no: EM13303620

Questions Cloud

What is the shortest possible length of the string : The wave function y(x, t) for a certain standing wave on a string fixed at both ends is given by y(x, t) = (0.05 m) sin (1.8 m-1x) cos (400 s-1t). What is the shortest possible length of the string
What type of tax rate structure does the u.s. tax system app : What type of tax rate structure does the U.S. tax system apply and what are the individual tax forms, and what factors are used to determine which one to use?
Determine the height of the water in the tank at any time : Outflow of water occurs from a cylindrical tank with a hole at the bottom. Find the height of the water in the tank at any time if the tank has a diameter 2 m, the hole has diameter 1 cm, and the initial height of the water when the hole is opened..
How accurately would each 100-ft distance have to be measure : How accurately would each 100-ft distance have to be measured so that the 95% error would no exceeded +-0.24ft in a total distance of 4000ft
Compute the distance when the traffic signal turns red : A driver with his passenger vehicle is driving at 35 mph, when the traffic signal in front of him changes to yellow. He is 100 feet from the intersection when he applies the brakes after a 1-second reaction time.
Calculate the separation distance of the wires : Two long parallel wires carry currents of 2.71 A and 5.93 A. Find the separation distance of the wires
Find how many turns does this solenoid contain : A current of 7.87 A in a solenoid of length 12.0 cm creates a 0.357-T magnetic field at the center of the solenoid
Compute the max acceptable tensile service load for angle : The service live load is three times the dead load. The 4-in leg contains a single line of 7/8 inch diameter bolts, and the 6 inch leg contains a double gage line of 7/8 inch diameter bolts.
Determine the amount of merchandise inventory lost : Complete the Balance Sheet using the information on the Post Closing Trial Balance and determine the amount of Merchandise Inventory lost and prepare the entry to write off the lose.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What bolt sizes must be used for the allowable shear stress

A structural steel beam is attached to a column with bolts. The downward force on the connection is 150 kips. What bolt sizes must be used if the allowable shear stress is 25.0 ksi

  The development of complex algorithms that can mine mounds

The development of complex algorithms that can mine mounds of data that have been collected from people and digital devices have led to the adoption of data mining by most businesses as a means of understanding their customers better than before

  Determine what is the total elongation of the pipe

a prismatic bar AB of length L, cross section A, modulus of elasticity E, and weight W hangs vertical under its own weight. if the bar is a riser pipe hanging from a drill rig at sea, what is the total elongation of the pipe

  Determine what force was needed to buckle the bar

On a very hot day, I saw a 1.6 meter long steel bar held between two rigid supports that had buckled due to the heat. The bar had a cross section of 10 mm by 40 mm, and I assume was A36 steel.

  Is crack width permissible assuming the exposure is dry air

Determine the estimated width of flexural cracks that will occur in the 8" (total depth) one-way slab shown in the figure below. Assume bottom clear cover is3/4". is the crack width permissible assuming the exposure is dry air

  Drawing the shearing force diagram

Draw the shearing force diagram and the moment diagram of the following problem. The beam is indeterminate. You need to integrate the moment twice to get a formula for the deflection v(x).

  Find what fraction of the population would make per year

Suppose there were reason to believe that incomes in some population were normally distributed, with a mean of $47,000 per year, and a standard deviation of $5,500 per year.

  Explain how to determine the final velocity of the crate

the 100 kg crate is originally at rest on the smooth horizontal surface. If a 200 newton force, acting at an angle of 45 degrees, is applied to the crate for 10 seconds. Determine the final velocity of the crate.

  Filter in each filter cycle

a) What flow rate (m 3/s) does the filter handle during production? b) What volume of water is needed for backwashing plus rising the filter in each filter cycle?

  Calculate net present value

Set up life cycle diagram for both alternatives and calculate net present value (NPT) and annual cost for the life time.

  Rate of diameter increasing of a balloon

A balloon is being inflated at the rate of 15m^3/min. At what rate is the diameter increasing after 5 min? Assume that the diameter is zero at time zero.

  Design of wastewater treatment plant for a community

Consider the design of wastewater treatment plant for a community wiyh average daily and peak hourly wastewater design flows of 2.0 mgd. The raw sewage has an average of 230 mg/l BOD5 and 260 mg/l of suspended solids.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd