User Account

All Pages

Compute the astm grain size number for this alloy be

Assignment Help Mechanical Engineering
Reference no: EM13609009

A photomicrograph was taken at a magnification of 500X and it was determined that the average number of grains per square inch in this photomicrograph is 10. Compute the ASTM grain size number for this alloy. Be careful, this picture is not taken at 100X. You will first need to calculate the number of grains per square inch at 100X.

Reference no: EM13609009

Questions Cloud

Jonas lumber company owns a 16660-acre tract of timber : jonas lumber company owns a 16660-acre tract of timber purchased in 2005 at a cost of 3094 per acre. at the time of
A company had the following results last year sales 700000 : a company had the following results last year sales 700000 return on investment 28 and margin 8. the average operating
A pellet gun is fired straight downward from the edge of a : a pellet gun is fired straight downward from the edge of a cliff that is 12.2 m above the ground. the pellet strikes
Alternative joint-cost-allocation methods further-process : alternative joint-cost-allocation methods further-process decision. the wood spiritscompany produces two
Compute the astm grain size number for this alloy be : a photomicrograph was taken at a magnification of 500x and it was determined that the average number of grains per
X company uses a fifo inventory system the actual cost of : x company uses a fifo inventory system. the actual cost of direct materials and direct labor is used to value labor and
A dynamite blast at a quarry launches a rock straight : a dynamite blast at a quarry launches a rock straight upward and 2.3 s later it is rising at a rate of 14 ms. assuming
Koko company produces lamps that require 225 standard : koko company produces lamps that require 2.25 standard hours per unit at an hourly rate of 15 per hour. if 7700 units
A large parallel plate capacitor has plate separation of : a large parallel plate capacitor has plate separation of 0.92 cm and plate area of 266 cm2. the capacitor is connected

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd