Compute the amount of primary consolidation settlement that

Assignment Help Civil Engineering
Reference no: EM13564990

A compressible 12-ft clay layer beneath a building is overlain by a stratum of sand and gravel and underlain by impermeable bedrock. The total expected primary consolidation settlement of the compressible clay layer due to the building load is 4.60 in. The coefficient of consolidation (cv) is 9.04 X 10^(-4) inches^(2)/minute.

1) How long will it take for 90% of the expected total primary consolidation settlement to take place?

2) Compute the amount of primary consolidation settlement that will occur in 1 year.

3) How long will it take for primary consolidation settlement of 1 inch to take place?

Reference no: EM13564990

Questions Cloud

Draw each of these circumstances and describe why each : Define flow at a hydraulic jump (upstream and downstream) in terms of the types of flow and corresponding Froude number. What is the depth of water at each section (upstream and downstream) compared to critical depth?
Will the vc meet minimum ssd standards if speeds can : A particular crest vertical curve (VC) on US 280 at Shelton Mill Rd has long been criticized as being unsafe. Its length is 400 feet. The prevailing speed on the crest VC is 50 mph
Determine the maximum possible flame temperature : Consider your cooking gas contains 80% propane and 20% butane. While burning on a cooktop, assume it burns with 200% excess air. If no heat is lost, determine the maximum possible flame temperature.
Find the coefficient of permeability of the clay for : A laboratory consolidation test was performed on a clayey soil specimen, which was drained on both top and bottom. The time for 50% consolidation was 6.2 minutes, and the specimen's thickness at 50% consolidation
Compute the amount of primary consolidation settlement that : A compressible 12-ft clay layer beneath a building is overlain by a stratum of sand and gravel and underlain by impermeable bedrock. The total expected primary consolidation settlement of the compressible clay layer due to the building load is 4.60 i..
What are the density volume-to-capacity ratio and level : A 5% upgrade on a six-lane freeway (three lanes in each direction) is 1.25 mi long. On this segment of freeway, the directional peak-hour volume is 3800 vehicles with 2% large trucks and 4% buses (no recreational vehicles), the peak-hour factor is 0...
How much heat had to be transferred to the vessel : Alkaloids are chemical compounds containing nitrogen that can be produced by plant cells. In an experiment, an insulated closed vessel 1.673 m3 in volume was injected with a dilute water solution containing two alkaloids: ajmalicine and serpentine.
Calculate the axial strain and the transverse strain in the : A rigid rectangular shelf is suspended from a rigid ceiling by mean of four rods of diameter .505 inches. The two rods to the left L1 and L2, are made of steel
What is the stress along the top edge and the bottom edge : A horizontal pre-stressing force of 500kN is applied to rectangler beam. the beam has a depth of 500mm and a width of 250mm. the force is applied at a distance of 80mm below the x-x axis. what is the stress along the top edge and the bottom edge caus..

Reviews

Write a Review

Civil Engineering Questions & Answers

  What would side slope of cut be if catch point is located

A backsight reading of 2.56 was obtained with rod at A and a foresight reading of 7.45 was obtained with the rod at the trial point B. If B is located 37.00 feet from the center line of a planned 50-foot wide road, is the catch point located uphi..

  Estimate the radon concentration in the crawl space

The emission rate of radon into the crawl space is reported to be 0.6 pCi/m^2-s. An exhaust system was added to provide 1 air exchange per hour (ACH) in the crawl space. The outdoor concentration of radon is 1 pCi/L.

  What is the net upward force exerted

the pressure inside a commercial airliner is maintained at 1.00 ATM. what is the net upward force exerted on a (1.0 m)(200 cm) cabin door if the outside pressure is 0.30 ATM?

  What is the average length of queue

Vehicles arrive at a toll booth with a mean arrival rate of 2 veh/min (the time between arrivals is exponentially distributed). The toll booth operator processes vehicles (collects tolls) at a uniform deterministic rate of one every 20 seconds. Wh..

  Resulting center of gravity

The section of the plywood in the 3rd quadrant is sawed off and the resulting piece is then glued squarely over the 4th quadrant portion of the plywood with glue of negligible weight.What are the x- and y-coordinates of the resulting center of gra..

  Find the maximum principal effective stress at failure

Given the initial effective stress state at a point within a soil mass (s_y=2.5 daN/cm2, s_x=1.5 daN/cm2, t_xy=t_xy=0.4 daN/cm2) and effective soil shear strength parameters at the same point

  Determine the concentration of ubod in the effluent

If the length of the river connection between the two lakes is equal to 3km and the velocity in the river is equal to 0.4 m/s, determine the concentration of UBOD in the effluent from the second lake.

  Determine what size motor-horsepower is required for mixer

A chemical mixing basin is to be designed to blend chlorine and treated wastewater. The basin flow is 700 gallons per minute and the basin dimensions are 5 feet by 5 feet by 5 feet water depth.

  Determine the number of kilograms of chlorine needed per day

Consider again the proposed water treatment plant for a city of 100,000 people where the maximum daily water usage rate is 99 X 106 L/d. Determine

  Estimate the diameter of the small pipe

Fluid flows steadily, at a volume rate Q, through a large pipe and then divides into two small pipes, the larger of which has an inside diameter of 25 mm and carries three times the flow of the smaller pipe.

  Calculate bulk specific gravity nd apparent specific gravity

A sample of coarse aggregate weights 1072 grams when oven-dried, 1091 grams when saturated surface-dried, and 667.6 grams when submerged. Calculate the bulk specific gravity, apparent specific gravity, and percent absorption.

  Explain whether or not if the wire will fracture

Consider a tensile test on polycrystalline copper which has a yield strength of 20,000 PSI and a tensile strength of 40,000PSI. The engineering strain at maximum load in a tensile test was 25%.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd