Compute the amount of chlorine required for disinfection

Assignment Help Civil Engineering
Reference no: EM13310432

Compute the amount of chlorine required for disinfection in pounds per day(lb/d). Estimate the annual cost for disinfection using chlorine.
Flow Rate= 30 milloin gallons per day.

Reference no: EM13310432

Questions Cloud

Ultraceuticals : Investigate “Ultraceuticals” . Choose one of these to be the basis of your assignment.
How much charge can the cloud hold : Lightning As a crude model for lightning, consider the ground to be one plate of a parallel-plate capacitor, How much charge can the cloud hold before the dielectric strength of the air is exceeded
Determine appropriate dimensions of the finished water : Determine appropriate dimensions of the finished water clearwells to achieve adequate disinfection using chlorine. Flow Rate Q = 30 million gallons paer day.
Explain any organic and inorganic reagents : Write equations and show how the following molecules can be prepared from any organic and inorganic reagents.
Compute the amount of chlorine required for disinfection : Compute the amount of chlorine required for disinfection in pounds per day(lb/d). Estimate the annual cost for disinfection using chlorine. Flow Rate= 30 milloin gallons per day.
What is the new magnification : An object is 2 m from the front side of a 1 m focal lenth converging lens. A second converging lens with focal length 2 m is placed 1 m from the first on the opposite side from the object. What is the new magnification
Calculate the detention time-hr in each clarifier : A waste water treatment plant previously used two circular clarifiers for primary settling, each 42 ft in diameter and 12 feet deep. Assume the incoming flow rate was 0.9 MGD. The maximum allowable clarifier loading rate is 600 gal/d/ft^2
Find out the poh of ammonia solution : A) Determine the [OH-] of a 0.16 M ammonia solution. B) Determine the pH of a 0.16 M ammonia solution. C) Determine the pOH of a 0.16 M ammonia solution.
Find the diameter of the path followed by the alpha particle : An alpha particle, which is a helium nucleus, has a mass of 6.64*10^-27 kg. It is travleing horizontally at 42.3 km/s when it enters a uniform, What is the diameter of the path followed by the alpha particle

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine the deflection of a simple uniformly loaded

Determine the deflection of a simple uniformly loaded beam by the Ritz method,using first one term, then two terms, adn finally three terms in a sine series. Why does the coefficient of sin2piex/L vanish?

  Resultant force from all fluids

A tank is filled with oil (specific gravity 0.8) and water to a depth of 10 meter and 6 meter respectively. Find the resultant force from all fluids acting on the gate of 1.8 meter by 9 meter.

  Find the factor of safety based on the ultimate force

An eighteen inch diameter sandstone column is subjected to an axial compressive force of 2x10^6 lb / ft. Find the factor of safety based on the ultimate compressive force. For the ultimate compressive stress of sandstone=85Mpa.

  Determine the terminal velocity of the block of cube

A fluid film 0.1 mm thick separates solid and surface. The fluid viscosity is 0.04 N*sec/m^2. Assuming the velocity distribution in the film is linear, find the terminal velocity of the block. The area of the cube in contact with the film is 0.25 ..

  Designing the tangent vertical curve

Due to a street crossing a roadway, the elevation of the roadway at station 3 +413.760 must be at 129.388 m. Design the curve?

  Tighten the packing on a leaking argon valve

A worker needs to enter a confined space to tighten the packing on a leaking argon valve. Describe two procedures that could be used to isolate the argon line and valve prior to starting work.

  What is the velocity of the projectile at the end of process

For simplicity assume the catapult consists of the piston-cylinder geometry (with the piston as the projectile) and that it is positioned horizontally. The steam initially occupies a volume of 1 liter at a pressure of 200 kpa.

  Determine the students final angular velocity

This causes the student to begin to rotate. Find the student's final angular velocity. The moments of inertia of the wheel and of the student are 0.313 kg · m2 and 2.09 kg · m2 respectively.

  What considerations would made with regards to cement type

You are a construction engineer working on a large concrete foundation project, involving the placement of over 500,000 c.y of concrete. The construction site is adjacent to a salt-water source (bay) & it is decided to set up a concrete batch plan..

  Determine effective annual interest rate for a nominal rate

Determine the effective annual interest rate for a nominal rate of 8% per year, in which is compounded quarterly.

  Determine force exerted by the hydraulic cylinder on boom

A hoist mechanism is attached to the back of a pickup truck. The crate being moved by the hoist shown below weighs 200 lbs. Note: Point A is directly above point B and the vertical distance between points A and B is 16 inches.

  Estimate the diffusion distance of a carbon atom in fe

The variation in the diffusion coefficient with temperature, over an appropriate range of temperature, can usually be approximated as follows: D= (D0)e^-(Q/(KT) where, Q = activation energy (eV/atom) and k = Boltzmann's constant (8.616*10-5 eV/ato..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd