Compute peak value of rms output voltage and power

Assignment Help Electrical Engineering
Reference no: EM13293017

a Three phase to single phase converter employs a 6 pulse bridge circuit. This device is fed from 400V,50 Hz supply through a delta/stare transformer whose per phase turns ratio 3:1. Foran output frequency of 2Hz, the load reactance is w0L =3ohm. The load resistance is 4 ohms.The commutation overlap and tyristor turnoff time limit the firing mode to 1650.Compute (a) peak value of rms output voltage (b) rms output current (c) outputpower

Reference no: EM13293017

Questions Cloud

Explain a standard galvanic cell the half-reactions : If you built a standard galvanic cell using the following half-reactions, what is the maximum work that could be done by this standard cell? (deltaG=wmax)
Explain the benefits and risks of debt financing : If Touring Enterprises were to increase the percentage of debt in its capital structure, what would happen to the WACC ? No calculation is necessary- simply provide a short, non-numeric response.
Calculate the cutoff frequency of the dominant mode : Calculate the cutoff frequency of the dominant mode and determine how many modes are passed at three times cutoff frequency of dominant mode and calculate the cutoff frequency of the dominant mode
Find the magnetic field at the center of this loop : A circular loop of wire with 10 turns, radius 0.241 m and resistance 0.235 Ohms is connected to a 13.1 V power supply. find The magnetic field at the center of this loop
Compute peak value of rms output voltage and power : a Three phase to single phase converter employs a 6 pulse bridge circuit. This device is fed from 400V,50 Hz supply through adelta/stare transformer whose per phase turns ratio 3:1. For an output frequency of 2Hz, the load reactance is w0L =3ohm.
Which capital budgeting method is most useful for evaluating : Which capital budgeting method is most useful for evaluating the following project?
What are the ideal and minimum possible temperatures : A temperature transmitter has an input range of 0 to 100 degrees celsius, an output range of 4 to 20 mA, and anaccuracy of ± 0.5%. The ideal transmitter has a linear output from 4 mA at 0 degrees celsius to 20 mA at 100 degrees celsius.
Would all financial managers view return trade-offs : What is the relationship between financial decision making and risk and return? Would all financial managers view risk/return trade-offs similarly? Why or why not?
Explain the rate of the reaction if [a] is doubled : What is the rate of the reaction if [A] is doubled. Starting with the original concentrations, what is the rate of the reaction if [B] is doubled

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design a circuit that has a port impedance of 1uf

Assume all that youhave a single 1nF capacitor, any number of op amps,and any numberof resistors. Design a circuit that has a port impedance of1uF.

  Derive minimal boolean expressions for flip-flop outputs

Design a 2-bit counter that, when f = 1, counts in the repeating sequence: 0, 2, 3, and when f = 0, counts in the reverse direction. Use T flip-flops. (a) Construct a state diagram or state table.

  Design a combinational circuit that accepts a 4-bit number

Design a combinational circuit that accepts a 4-bit number and generates a 3-bit binary number output that approximates the square root of the number. For example, if the square root is 3.5 or larger, give a result of 4.

  Find the midband gain from base to collector neglecting ro

The amplifier has Rsig = RL = 1K, Rc = 1K, Rb = 47K, Beta = 100, Cu = 0.8 pF, and Ft = 600MHz. Assume the coupling capacitors to be very large. A.) find the DC collector current of the transistor. B.) find gm and Rpi

  Find the value of power gain in db of an amplifier

An amplifier with a voltage gain of +40 dB, an input resistance of 10 kO, and an output resistance of 1 kO is used to drive a 1-kO load. What is the value of Avo Find the value of power gain in dB

  Show how physical address is generated from alogical address

1- Name a few computer operating systems. 2- What is the full form for MS-DOS 3- What is the difference between a logical address and aphysical address

  Compare the noise floor in dbm with the gsm system

Compare the noise floor in dBm with the GSM system (BW= 200 kHz) used by the European cell standards (available today in the US thru the AT&T acquired from the Cingular systems) assuming the same noise figure (NF) of 10 dB for the same receivers.

  Determine what is the lenght of the sequence

Let x[n], y[n] and w[n] denote three finite-lenght sequences of lenghts N, M, and L, respectively with the first sample of each sequence occuring at n=0. What is the lenght of the sequence x[n] * y[n] * w[n]

  Determine whether the discrete signals given are periodic

Determine whether the discrete signals below are periodic. If the signal is periodic, determine the number of  samples per period. (a) x[n]=cos(πn) (b) x[n]= -3sin(.01πn) (c) x[n]= 1+cos((πn)/2)

  Compute the fourier transform of the descret time signal

compute the fourier transform of the descret time signal x[n] = {C, n1

  Design that shows the exact values of all components

When the variable resistor is adjusted to one extreme position the overall circuit voltage gain should be 3. When the variable resistor is adjusted to its other extreme position the overall circuit voltage gain should be 13.

  Explain what are the operator error specs of devices

When working with laboratory equipment such as Digital multimeter, Thermocouple, and data acquisition unit what are the operator error specs of devices, polynomial correction

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd