Compute current in the element voltage across element

Assignment Help Electrical Engineering
Reference no: EM13290043

The charge entering the + terminal of an element is q(t) =-12e^-2t mC. if the power delivered to the element is p(t) =2.4e^-3t W. Compute the current in the element, the voltage acrossthe element and the energy delivered to the element in the timeinterval 0 < t < 100 ms.

Reference no: EM13290043

Questions Cloud

Calculate the firm economic order quantity : Mama Leone's operates 250 days per year and maintains a minimum inventory level of 2 days' worth of cheese as a safety stock. If the lead-time to receive orders of cheese is 3 days, calculate the reorder point.
What is the equivalent resistance for the ammeter : A meter has a resistance of 100Ω and gives a full scale deflection when it carries a currentof 25 μA. (a) What resistor, Rx, would you connect in parallelwith this meter in order to construct an ammeter which gives afull-scale deflection for a cur..
Calculate icy treats minimum and peak funding requirements : During the slow winter period the firm holds $10,000 in cash, $55,000 in inventory, $40,000 in accounts receivable, and $35,000 in accounts payable. Calculate Icy Treats' minimum and peak funding requirements.
What are the equivalent decimal and hexadecimal numbers : What is the largest binary number which can be expressed with 13 bits What are the equivalent decimal and hexadecimal numbers
Compute current in the element voltage across element : The charge entering the + terminal of an element is q(t) =-12e^-2t mC. if the power delivered to the element is p(t) =2.4e^-3t W. Compute the current in the element, the voltage acrossthe element and the energy delivered to the element in the time..
Define why two layers formed when 3 m naoh : Explain why two layers formed when 3 M NaOH was added to the ether solution after the initial separation. What solvents do the two layers represent? Which solvent forms the upper layer? Why?
What is the average dividend growth rate : Highway Express has paid annual dividends of $1.16, $1.20, $1.25, $1.10, and $0.95 over the past five years respectively. What is the average dividend growth rate?
What required reserve ratio is implied : If the bank holds $65 million in deposits and currently holds bank reserves such that excess rerves are zero, what required reserve ratio is implied?
What is the bullets time of flight : A rifle is aimed horizontally at a target 1,234.37 m away. What is the bullet's time of flight

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the modulation index

Consider a signal x(t) = 10 cos(2pi*fct + 4 cos 2pi*fmt). Assume frequency modulation. The message frequency fm = 2:3 kHz. Calculate the modulation index and find the bandwidth when.

  How to design a proportional control law

where V is given in meters per second, U is in degrees, and W is the percent grade of the road. Design a proportional control law U = -kp V that will maintain a velocity error of less than 1 m/sec in the presence of a constant 2% grade.

  Find the capacitance and inductance of the matching network

The amplifier is connected to the handset antenna which has an impedance of 35 + j10 at one unspecified operating frequency. Find the inductive reactance and capacitive reactance needed to match the transmitter output to the antenna

  Design a full subtractor circuit which computes a-b-c

Design a full subtractor, that is a circuit which computes a-b-c, where c is a borrow from the next less significant bit. (Hint: Denote the difference as d, and a borrow from the next more significant bit as p, then develop a truth table for the p..

  Design a ram neccessary combinational circuit

Design a 1024x16 RAM using the 256x8 RAM blocks and neccessary combinational circuit. Note that, 256x8 RAM block has 8 bit data (DATA), 8 bit address (ADRS), chip select (CS), read/write (R/W) inputs and a three-state output bus.

  Determine the frequencies of aliasing noise

given analog signal : x(t)=8cos(6,000pi)+5cos(14,000pit) t>=0 sampled at rate 12,000 Hz a) sketch the spectorum of the orignal signal and the sampled signal from 0 KHz and 25 KHz.

  Calculate the line-lo-line voltage at sending end of feeder

The transformer is supplying a load of 325 MVA, with 0.93 power factor lagging at a voltage of 24 kV (line-to-line) on its low-voltage side. It is supplied from a feeder whose impedance is 0.11 + j2.2 ohms connected

  Find the transfer function and resolution

find the transfer function and resolution for a 10-turn, 4.7k potentiometer with 3450 degrees of rotation and a 0 to 5 volt output. calculate the resolution in ohms per volt

  Design a first order low pass filter with a dc gain of 2

design a first order low pass filter with a DC gain of 2 and a gain of -3 decibels at 1000 rad/s. not sure what design equations to use since there not seem to be a given cut off frequency.

  Find out the voltage required on the input

Determine the voltage required on the input of the amplifier to give the maximum output of 85 dBuV. If the signal level from the aerial is 5 dBmV and the input noise level is 20 dBuV, calculate the signal-to-noise ratio on the output of the amplifi..

  How much energy is used by the resistor in 5 min

A 26 resistor is connected across a 65 V battery. How much energy is used by the resistor in 5 min

  Write down the generic form of the convolution integral

For x(t) --> Linear System --> y(t), x(t) = u(t)-u(t-1) and h(t) = 2e^-t*u(t)  Sketch x(t) and h(t) Write down the generic form of the convolution integral Calculate y(t) for t 1, using the convolution integral method.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd