Compare the three solutions and comment on the error

Assignment Help Electrical Engineering
Reference no: EM13262160

1. A Si pn junction diode is described by its I-V equation, I?= Is exp (V?/V?) ,where V?=25mV, Is=10-14A . It is desired to derive constant drop and PWL models for the diode assuming an operating current between 1mA and 3mA.
a) Compute the constant drop model parameter, VDo.
b) Compute the piece wise linear (PWL) model parameters: VDo, rD.
c) Plot in the same graph the real diode I-V curve and the CD and PWL models.

2. The above described diode is included in a simple circuit in series with a DC power supply, VS=10V and a resistor, R=5k?

a) Use the numerical iterative procedure to compute the exact solution (ID, VD).

b) Use the CD model derived in problem 2 to find an approximate solution for (ID, VD).

c) Use the PWL model derived in problem 2 to find an approximate solution for (ID, VD).

d) Compare the three solutions and comment on the error.

3. Repeat problem 3 with VS=10V, and R=1k? (different diode operating region!)

a) Use the numerical iterative procedure to compute the exact solution (ID, VD).

b) Use the CD model derived in problem 2 to find an approximate solution for (ID, VD).

c) Use the PWL model derived in problem 2 to find an approximate solution for (ID, VD).

d) Compare the three solutions and comment on the error. Is it higher than in prob 3? Why?

Reference no: EM13262160

Questions Cloud

How to calculate the potential of the cell : Calculate the potential of the following cell and indicate whether the reaction is expected to be spontaneous
Determine the abcd constant of the line : A three-phase, 345-kV, 60-Hz transposed line is composed of two ACSR 1,113,000, 45/7 Bluejay conductors per phase with flat horizontal spacing of 11 m. The conductors have a diameter of 3.195 cm and a GMR of 1.268 cm.
Compute the potential of the following cell : Calculate the potential of the following cell and indicate whether the reaction is expected to be spontaneous. Cr + 3 Ag+ ---> Cr3+ + 3Ag
What is the acceleration of a rising hot-air balloon : What is the acceleration of a rising hot-air balloon if the ratio of the air density outside the balloon to that inside is 1.37?
Compare the three solutions and comment on the error : A Si pn junction diode is described by its I-V equation, I?= Is exp (V?/V?) ,where V?=25mV, Is=10-14A . It is desired to derive constant drop and PWL models for the diode assuming an operating current between 1mA and 3mA.
Explain the specific heat of the solution can be assumed : The temperature after the reaction is 25.23 C. If the density of final solution is 1.02 g/mL, calculate q, if the specific heat of the solution can be assumed to be equivalent to that of water.
What is the expected return and standard deviation : What is the expected return and standard deviation for the minimum-variance portfolio of the two risky funds?
Determine the impulse delivered to the ball : In a slow-pitch softball game, a 0.200 kg softball crossed the plate at 18.00 m/s at an angle of 45.0° below the horizontal. Determine the impulse delivered to the ball
Determine the no-load line-to-line generated voltage : A three-phase, 318.75-kVA, 2300-V alternator has an armature resistance of 0.35 ­/phase and a synchronous reactance of 1.2 ­/phase. Determine the no-load line-to-line generated voltage and the voltage regulation

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Design a 3 rd order high - pass butterworth filter

Design a 3 th order high - pass Butterworth filter with a High Frequency gain of 20 DB and a cutoff frequency of 20 rad/s. 2) Using MATLAB, plot the frequency respon se of this filter, and the location of the filter poles.

  Design a phase shift circuit at a frquency

1- Draw a circuit whose output goes to + V sat . When the input signal is below -4V. the output should be -V sat, when the input is above - 4V  2- Design a - 90 phase shift circuit at 1590 Hz , Then for your design calculate 0 at 15 Hz, & 15 KHz

  Define discrete sequence plot in matlab

Discrete sequence plot in Matlab, Consider the following formula, x[n] = x[n-1] + x[n-3] n>=3, find the rest of the sequence for 0

  How much will old lady need to save each month

A 40-year old person wants to accumulate $500,000.00 by age 65. How much will she need to save each month, starting one month from now, if the interest rate is 6% per year

  Determine what is the phase angle in degree

an electric motor has an armture constant of 140, a flux of 25 mwh, an armuture current of 30 A , and a rotatio?nal speed of 1600 rpm. what is most nearly the power output in watt

  Find the electric field produced by the two rods

Two thin rods of length L lie on the x axis. One of them has a charge of -Q uniformly distributed along its length and is positioned between x = -L and x = 0. The other one has a charge of +Q uniformly distributed along its length.

  Find the probability that the tenth phone installed

The probability that a person will install a black telephone in a residence is estimated to be 0.3. Find the probability that the tenth phone installed in a new subdivision is the fifth black phone.

  Find the steady state temperature distribution of the tray

The tray heats up according to ut = c2?u + h(x, y) where h(x, y) = 5(1 - sin(8πy)) and c2 = 10-4. Assume that u = 200 along each edge. Find the steady state temperature distribution of the tray.

  Determine signal parameters dc voltage and ac power

For random ergodic voltage signal, I make a histogram of sample voltages and note that they form a Gaussian distribution. estimate the following moments over a number of samples taken at diffrent time points alont the voltage signal

  Determine what is the value of the voltage source

A two-resistor voltage divider consists of a 10 k and a 15 k ohm resistor, with the 10 k resistor connected to the voltage source and the 15 k resistor connected to ground. If the output voltage is 2.5 V across the 10 k resistor

  Design an 8-bit register with 2 control inputs s1 and s0

Design an 8-bit register with 2 control inputs s1 and s0, 8 data inputs I7..I0, and 8 data outputs Q7..Q0. s1s0=00 means maintain the present value, s1s0=01 means load, and s1s0=10 means clear. s1s0=11 means to swap

  Use the bounce diagram to plot

The line is terminated in a load RL = 25 ohm. Use the bounce diagram to plot V(t) at a point midway along the length of the line from t = 0 to t = 25 ns.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd