Compare the mode shapes and resonances

Assignment Help Mechanical Engineering

Reference no: EM131594843

Assignment:

By using HyperMesh software, make a beam model similar to the below test model and find (Using Nastran) the mode shapes and resonances of the model.

Make your model with three following modelling methods:

1. Using 1-D BEAM Elements,

2. Using 2-D SHELL Elements, and

3. Using 3-D SOLID Elements.

Compare the mode shapes and resonances of the three modelling methods. Explain the reasons for possible slight discrepancies between different modelling methods.

Note: I suggest you to make a table and compare the corresponding resonant frequencies for 1D Beam, 2D SHELL, and 3D SOLID elements modelling methods (Six structural modes for each method are sufficient).

**A maximum 4 pages (including figures) report is sufficient.
**Submit your Homework on Learning Hub (Online) in PDF format, do not submit to reception.

Attention:

The below test results are only for your reading and information. My undergraduate students of Vehicle NVH course have conducted the below tests on the same size beam.

You may compare your own CAE results with the blow test results.

POLYETC LASER VIBROMETER (Notes about the experiment)

1. Beam material: Aluminium (Al), Width (W) = 50mm, Length (L) = 600mm' Thickness (t) = 10mm.

2. Apparatus for experiment:

2. Measurement results:

1) Resonances

Mode #	Measurement (Hz)
1	153.5
2	411.5
3	-
4	811.0

2) Model Shapes:

153.5 HZ

411.5 Hz

811.0 Hz

Reference no: EM131594843

Questions Cloud

Prepare a differential analysis : Prepare a differential analysis dated March 4, 2014, on whether to sell rough-cut lumber (Alternative 1) or process further into finished-cut lumber

What forces are at work demanding low-skilled labor : What forces are at work demanding low-skilled labor in the developing world? What could a country do to improve the types of skills demanded of its labor?

Writer describe the level of health insurance coverage in us : Writer describes the level of health insurance coverage in the United States and the financial protection provided by that coverage.

What is the minimum price per unit : Down Home Jeans Co. has an annual plant capacity of 64,700 units, What is the minimum price per unit that would produce a positive contribution margin

Compare the mode shapes and resonances : AUTO1026 & MIET2491 - Explain the reasons for possible slight discrepancies between different modelling methods.

How strong pressures stemming from each of the five forces : Case Study: Cooper Tire and Rubber Company- Identify and explain how strong the pressures stemming from each of the five forces are (low, moderate, high).

Calculate the inverse z-transform : Using the partial fraction method, calculate the inverse z-transform of the following DT causal sequences.

What is the unit cost : Required - What is the unit cost below which Forever Ready Company should not go in bidding on the government contract

Calculate unilateral z-transform of given causal functions : Calculate the unilateral z-transform of the following causal functions.

Reviews

len1594843

8/9/2017 2:07:03 AM

By using HyperMesh software, make a beam model similar to the below test model and find (Using Nastran) the mode shapes and resonances of the model. Make your model with three following modelling methods: 1. Using 1-D BEAM Elements, 2. Using 2-D SHELL Elements, and 3. Using 3-D SOLID Elements.

len1594843

8/9/2017 2:06:48 AM

Hey hi, I have attached my assignment, which need to be done in hypermesh. Just go through the PDF it says all. I have already given you 2 assignments in the past which are successful. I'm looking forward for this to be done in time with good solution. Thanks. I want it before 9pm of August (Melbourne time)

Write a Review

Required(*) Message

Mechanical Engineering Questions & Answers

Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

Automatic control

DOF system and Find the differential equation describing the system

Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

User Account

All Pages