Cold cranking amperes of a conventional lead-acid

Assignment Help Mechanical Engineering
Reference no: EM13704529

The cold cranking amperes (CCA) of a conventional lead-acid automobile battery is the amount of current the battery can provide at 0°F for 30 seconds and minute in at least 1.2 volts per cell (or 7.2 volts for a standard 12-volt battery). If a battery is rated for 700 CCA, how much work will it deliver to the starter motor, assuming the minimum voltage (7.2 V) and maximum time (30 s) are required?

Reference no: EM13704529

Questions Cloud

A hypothetical metal has hcp crystal structure with ideal : A hypothetical metal has an HCP crystal structure with the ideal c/a ratio (1.633). What is the volume of its unit cell, if the atomic radius is 1.3A?
Determine the tension in cable ac : The boom OA carries a load P and is supported by two cables as shown. Knowing that the tension in cable AB is 183 lb and that the resultant of the load P and of the forces exerted at A by the two cables must be directed along OA, determine the tensio..
Calculate the work done by the steam during this process : Five kilogram of saturated water vapor at 300 kPa is heated at constant pressure until its temperature reaches 200oC. Calculate the work done by the steam during this process.
Determine the value of the polar coordinates of the point : A particle moves along a spiral described by the equation r=r(inital)+kappa*theta, where r(inital) and kappa are constants, and where theta is in radians. Assume that theta dot =alpha*time, where alpha= 0.15rad/s^2 and t is time expressed in seconds.
Cold cranking amperes of a conventional lead-acid : The cold cranking amperes (CCA) of a conventional lead-acid automobile battery is the amount of current the battery can provide at 0°F for 30 seconds and minute in at least 1.2 volts per cell (or 7.2 volts for a standard 12-volt battery). If a batter..
Aircraft executes horizontal turn at constant true air speed : In a correctly banked turn of radius R, an aircraft executes a horizontal turn at constant true air speed, V, with no sideslip and zero roll rates. The aircraft must bank at an angle phi from the horizontal so that the horizontal component of its lif..
Write the relational schema : Write the relational schema, draw its dependency diagram, and identify all dependencies, including all partial and transitive dependencies.
Calculate the average test score and display it : Write a program that asks for five test scores. The program should calculate the average test score and display it. The number displayed should be formatted in fixed-point notation, with one decimal point of precision.
Write a program to find a baseball players batting average : Write a program to find a baseball player's batting average. The program should ask the user to enter the number of times the player was at bat and the number of hits he got. It should then show his batting average to four decimal places.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Evaluate the effect of the water spray on efficiency

Evaluate the effect of the water spray on efficiency (net work out divided by heat input) and net power out per kg/s of dry air coming into the turbine.

  Determine the torque t and power p that can also act

a solid shaft 200 mm in diameter rotates at f 20 revsec and is subjected to a bending moment of 21p kn.m. determine

  Heat transfer to the air in the heating section

Air at 14.7 psia, 50oF, and 60% relative humidity is first heated to 72  o F in a heating section and then humidified by introducing water vapor. The air leaves the humidifying section at 75oF and 55% relative humidity.

  Calculate the density of air in lbmft3 at standard

a. calculate the density of air in lbmft3 at standard conditions 75f and 14.7 psia assume m 28.9 lbmlb-mol.b.

  Determine the maximum exit velocity for this nozzle

Air enters an adiabatic nozzle at 5.18 MPa and 400K with a velocity of 20 m/s. The air exits at 2.00MPa. Determine the maximum exit velocity for this nozzle.

  Determine if a simple supported w12 x 26 a36 steel beam

determine if a simple supported w12 x 26 a36 steel beam has the capacity to support loads that produce 50ksi of

  What is the appropriate model tow velocity in ms a boat of

a boat of length 50 m is designed to cruise at 30 mph and is to be tested in a tow tank with a model of length 0.5 m.

  Determine the stresses and strains in the bar

Also determine the axial force and deformation of the diameter due to temperature rise. Let E = 120 GPa and Co-efficient of linear thermal expansion = 0.0000168 per °C.

  A tube of diameter 50 mm having a surface temperature of

a tube of diameter 50 mm having a surface temperature of 85degc is embedded in the center plane of a concrete slab

  A body with the shape of a rectangular parallelepiped

a body with the shape of a rectangular parallelepiped moves without slipping on two cylindrical rollers. the mass os

  After the compression process the pressure in the cylinder

a well insulated piston cylinder device containing 3 lbm of water is compressed using 601 kj of energy. initially the

  If the 50 kg crate starts from rest and attains a speed of

if the 50 kg. crate starts from rest and attains a speed of 6ms when it has traveled a distance of 15m. determine the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd