Closed-loop geothermal heat pump

Assignment Help Mechanical Engineering
Reference no: EM13949860

1. Identify and visit a local facility that uses cold thermal storage. Conduct a forensic study to determine if the cold storage system is well-suited for the given application today. Consider costs, effectiveness in providing the desired cooling, contribution to global climate change, and other pertinent issues. If the cold storage system is well suited for the application, document that. If the cold storage system is not well suited, recommend system upgrades or an alternative approach for obtaining the desired cooling. Prepare a PowerPoint presentation of your findings.

2. A vertical, closed-loop geothermal heat pump is under consideration for a new 50,000-ft2 school building. The design capacity is 100 tons for both heating and cooling. The local water table is 150 ft, and the ground water temperature is 558F. Specify a ground source heat pump as well as the number and depth of wells for this application and develop a layout of vertical wells and piping required by the system.

3. Investigate the economic feasibility of using a waste heat-recovery heat pump for domestic water heating that employs ventilation air being discharged from a dwelling as the source. Assume typical hot water use of a family of four living in a 2200-ft2 single-family dwelling in your locale. Write a report of your findings.

Reference no: EM13949860

Questions Cloud

Metabolic rate during surgery : In induced hypothermia, the temperature of a particular organ, such as the heart, is lowered to reduce the metabolic rate during surgery. Cooling is achieved by circulating blood through a heat exchanger  outside  the  body.
Technical readiness and economic feasibility : Investigate the technical readiness and economic feasibility for each concept. Report your findings in an executive summary and a PowerPoint presentation with at least three references.
Annotated list of food-cooling : A written report providing your recommendations is required, including an annotated list of food-cooling Dos and Don'ts for restaurants supplied by the company with fish.
Perform an inner join on tables books and sources. : Perform a Left Outer Join using tables BOOKS and ORDER_LINES. Show all the ISBNs in the BOOKS table and any associated ISBNs in the ORDER_LINES table.
Closed-loop geothermal heat pump : A vertical, closed-loop geothermal heat pump is under consideration for a new 50,000-ft2 school building. The design capacity is 100 tons for both heating and cooling.
Calculate the moving averages for this time series : From the fourth quarter of 1997 to the first quarter of 1998, revenues declined. What happened on a seasonally adjusted basis? From the first quarter of 1998 to the second quarter of 1998, revenues increased. What happened on a seasonally adjusted ba..
Focus on international issues : Differences between managerial and financial accounting Product costing in manufacturing companies
Introduction of a regenerative heat exchanger : The Brayton refrigeration cycle is modified by the introduction of a regenerative heat exchanger. In the modified cycle, compressed air enters the regenerative heat exchanger at 350 K and is cooled to 320 K before entering the turbine. Determine, ..
Problem regarding the compressor pressure ratio : 1. Plot the quantities calculated in parts (a) through (c) of Problem 10.43 versus the compressor pressure ratio ranging from 3 to 6. Repeat for compressor and turbine isentropic efficiencies of 90%, 85%, and 80%.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd