User Account

All Pages

Circuit in multisim and run a single frequency analysis

Assignment Help Other Engineering
Reference no: EM131077725

  • Consider the circuit demonstrated in this week's presentation. Analyze the circuit to determine the following (include both polar and complex forms where applicable):
  • Zeq
  • IT
  • IR1
  • IL1
  • Real Power (Watts)
  • Reactive Power (VARs)
  • Apparent Power (Vas)
  • Power Factor
  • Construct the circuit in MultiSIM and run a Single Frequency Analysis to confirm your calculations for the phasor values in part 2. Capture a screenshot of the analysis for both Magnitude/Phase (polar) and Real/Imaginary (complex). Create a table with your expected and measured results.
  • Measure the real power of the circuit and the power factor using a watt meter. Capture a screenshot of the watt meter readings.
  • Based upon the power factor, determine the value of the capacitors needed in each case to bring the power factor to the following values. Be sure to show your calculations.
  • Power Factor = 0.85
  • Power Factor = 0.95
  • Power Factor = 1.00
  • Insert each of the capacitor values found in step 5 into the circuit one at time and confirm the power factor correction with a watt meter. Use a 5% tolerance for the capacitors. Capture a screenshot of the watt meter for each case. Create a table of expected and measured results. Comment on how well the desired power factor was achieved and any reasons for discrepancies.

Reference no: EM131077725

Questions Cloud

Information to find the p-value : Assume that the significance level is α=0.1. Use the given information to find the P-value and the critical value(s). The test statistic of z=1.95 is obtained when testing the claim that p>0.8.
Multisim single frequency analysis : Construct the circuit with MultiSIM using a 5% tolerance for the resistor and the capacitor. Adjust the frequency according to the table below and obtain measurements from MultiSIM using AC Analysis and express in polar form.
Find the value of the test statistic : A random sample of 44 adult females has white blood cell counts with a mean of 8.95 and a standard deviation of 3.16. Find the value of the test statistic.
Compute this student''s grade-point average : Compute this student's grade-point average.
Circuit in multisim and run a single frequency analysis : Consider the circuit demonstrated in this week's presentation. Analyze the circuit to determine the following (include both polar and complex forms where applicable):
Describe responsibilities of the supervisee and supervisor : What questions would you have for your supervisor about any of the items included, if you were the supervisee receiving this agreement at your fieldwork site? How important would it be for you to have this type of agreement in place with your supe..
Write paragraph detailing importance of ten strategic points : Briefly write an introductory paragraph detailing the importance of the ten strategic points below then identify and Discuss/Summarize each of the ten points within the attached article in a short paragraph when possible.
What is the most controversial statement you have heard : What is the most controversial statement you've heard? What is the most important ethical issue that the movie is addressing? Please explain.
Do believe personal therapy must be requirement for learners : Do you believe personal therapy should be a requirement for learners who are preparing to become professional counselors? Why, or why not? Support your ideas with references to specific ethical standards and to a minimum of two peer-reviewed artic..

Reviews

Write a Review

Other Engineering Questions & Answers

  Does the operation of this circuit rely on charge storage

Figure shows a commonly used circuit of a D flip-flop that is triggered by the negative-going edge of the clock φ. (a) For φ high, what are the values of Q and Q in terms of D? Which transistors are conducting? If Dis high and φ goes low, which tr..

  Draw a circuit diagram to provide rotary actuation

Modify the design of the circuit shown in FIGURE 3 and draw a circuit diagram to provide rotary actuation in both directions using a single direction pump (to replace the bi-directional pump) and providing a means of preventing over-speeding in th..

  What are the five fluids used as damping media

What are the five (5) fluids used as damping media. Calculate the logarithmic decrements of the beam in these five fluids. Calculate the damping ratio of these five fluids and rank them from the highest to the lowest.

  Major design and implementation challenges

Our project is to design a functional jacket that will charge a mobile device on the go. Most people have had their cellphone lose charge at a time when it is inconvenient or impossible to recharge it. Our project aims to eliminate that problem by..

  Determine the frequency of the poles due to c1 and c2

Consider the circuit at midband frequencies. First, determine the small-signal voltage gain Vo /Vi . (Note that RG can be neglected in this process.) Then use Miller's theorem on RG to determine the amplifier input resistance Rin . Finally, determ..

  How much will the coffee that you poured the water into cool

In a refrigerator, heat is transferred from a colder area (the inside of the refrigerator) to a warmer area (the air outside of the refrigerator). Given what you know about internal energy, explain how this is possible.

  Question regarding the cross-sectional area

A coil with 380 windings is wound around a cast iron ring. the cast iron ring has a mean diameter of 125mm and a cross-sectional area of 600mm squared. The magnetic field strength is 3000Am while the relative permeability of the core is 780. deter..

  Principal of pressure transmitter

The principal of pressure transmitter, What is it capable of Pressure transmitter from Rosemont - Stability and Accuracy

  What ranges of values of vil and vih

If for its inverter, the output signals swing between 0 and VDD, the "gain-of-one" points are separated by less than 1 3 VDD, and the noise margins are within 30% f one nother, what ranges of values of VIL , VIH , VOL, VOH, NML, and NMH can you ..

  Estimate the final water temperature

Liquid water at 30.0°C and liquid water at 90.0°C are combined in a ratio (1 kg cold water/2 kg hot water). (a) Use a simple calculation to estimate the final water temperature. For this part, pretend you never heard of energy balances.

  How many bits are required in the instruction format

The instruction set architecture for a simple computer must support access to 64 KB of byte-addressable memory space and eight 16-bit general-purpose CPU registers.

  Formulate dr. konurs maximum-flow problem as a linear model

Represent Dr. Konur's problem on a network by defining the nodes, node values (if any), arcs, arc costs (if any), arc capacities (if any) and state it as a maximum-flow problem and mathematically formulate Dr. Konur's maximum-flow problem as a lin..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd