Changes in kinetic and potential energies are zero

Assignment Help Mechanical Engineering
Reference no: EM13710416

Water in a vertical piston cylinder is heated at constant pressure of 10 bar. It is initially at 179.9 0C and has a specific volume of 0.1 m3/kg and is heated to a final specific volume of 0.248 m3/kg. Changes in kinetic and potential energies are zero. Determine:

a) the initial quality of the water

b) the final temperature of the water vapor

c) the work in kJ/kg

d) the initial and final internal energy in kJ/kg

e) the heat transfer in kJ/kg

Reference no: EM13710416

Questions Cloud

Estimate how fast the baseball is moving : A 0.15 kg baseball collides with a 1.1 kg bat. The ball has a velocity of 43.5 m/s immediately before the collision. Estimate how fast the baseball is moving
What is the steady state surface temperature : A cylindrical electric resistance heater has a diameter of 1cm and length of 0.25m. When water at 30oC flows across the heater a heat-transfer coefficient of 15W/(m2oC) exists at the surface. If the electrical input to the heater is 5W, what is the s..
Determine the initial velocity of the mass : A 0.25 kg mass on a spring has a displacement x(t) = 0.2 cos(1.2 t - 0.15?). Determine the initial velocity of the mass
Exit temp of the air and the rate of heat transfer from air : Air enters the evaporator of an air conditioner at 14.7 psia, 90F, 200 ft3/min. R-134a at 20 psia, 30%  quality enters at 4 lbm/min and leaves as saturated vapor at the same pressure. Find the exit temp of the air and the rate of heat transfer from t..
Changes in kinetic and potential energies are zero : Water in a vertical piston cylinder is heated at constant pressure of 10 bar. It is initially at 179.9 0C and has a specific volume of 0.1 m3/kg and is heated to a final specific volume of 0.248 m3/kg. Changes in kinetic and potential energies are ze..
What is the angular frequency of this oscillator : A block of mass m= .6 kg is attached to a spring with a natural frequency of oscillation f= 1.45 Hz. What is the angular frequency of this oscillator
What should his speed have been at the top of the ramp : A physics professor did daredevil stunts in his spare time. His last stunt was an attempt to jump across a river on a motorcycle. What should his speed have been at the top of the ramp
Frictionless slot that lies in the vertical plane : The 8-lb block slides in a frictionless slot that lies in the vertical plane. The stiffness’s of springs A and B attached to the block are kA =40 lb/ft and kB= 20 lb/ft. When the block is in position 1, spring A is compressed 0.5 ft and spring B is u..
What is the magnitude of the dog velocity : A dog running in an open field has components of velocity vx = 3.5m/s and vy = -1.4m/s at time t1= 10.7s. For the time interval from t1 = 10.7s to t2= 19.1s, What is the magnitude of the dog's velocity

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the velocity of the canoe when it hits the bottom

a water ride at cedar point involves a 200 lb canoe that slides down a 45 degree incline from an original elevation of

  What is the ideal mechanical advantage of the system

A wheel barrow is used to lift a 200 lb load. The length from the wheel axle to the center of the load is 2 ft. The length from the wheel and axle to the effort is 5 ft. 5. What is the ideal mechanical advantage of the system?

  Many ventilation systems maintain a slightly higher pressure

Many ventilation systems maintain a slightly higher pressure in a building than the outside pressure. If the pressure in your room is 0.1 psi than the outside pressure will you be able to open the door? How much is this force compared to your weight?..

  Phase of the product development process

Identify and understand each phase of the product development process: The assignment includes the practical application of the first few phases of a PD process.

  Determine the exit temperature

Steam enters an adiabatic nozzle steadily, at 2.5 Mpa and 400°C with a velocity of 50 m/s and exits at 1 MPa and 380 m/s. If the nozzle has an inlet area of 65 cm2, determine: The exit temperature. The rate of entropy generation for this process, in..

  What statistical outcomes would distinguish a better player

As a game, slide a matchbook across a table, trying to make it stop at some predefined point on each attempt. Measure the distance from the starting point to the stopping point. Repeat this 10, 20, through 50 times. Plot the frequency distribution fr..

  A permanent magnet dc motor is coupled to a load through a

a permanent magnet dc motor is coupled to a load through a gearbox. if the polar moments of inertia of the rotor and

  Suppose you are a materials engineer working for a beverage

suppose you are a materials engineer working for a beverage company and have been asked to identify what material

  Create an anonymous function

Create three subplots (1x3) showing u(T),h(T) v/s Ton each subplot for these 3 pressures , with titles, labelled axes and create an anonymous function cp(a,b,c,d,n of these parameters and call it for Air at T=678°R

  Estimate the force of the roof at the opening pressures for

fluid mechanics for chemical engineers.nevers2-11large hydrocarbon storage tanks normally have a valve on their vents

  The temperature rise is brought about adiabatically by

a system consisting of air considered as an ideal gas initially at 400 k and 1 bar experiences the two different types

  At this point the piston is locked with a pin and

air in pistoncylinder at 200 kpa 600k is expanded in a constant-pressurenbspprocess to twice the initial volume state

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd