Challenges facing all-electric vehicle transportation

Assignment Help Mechanical Engineering
Reference no: EM13706617

One of the challenges facing all-electric vehicle transportation is the electrical infrastructure need to support rapid recharging of electric cars. Residential power circuits commonly supply alternating current (A/C) with maximum residential voltage of 220 Volts, and with maximum current of approximately 20 Amps. A gallon of gasoline contains roughly 125 MJ of energy when burned. How long would it take such that the electrical energy stored in an electric car battery would be equivalent to the chemical energy of 20 gallons of gasoline?

Reference no: EM13706617

Questions Cloud

What is the rotation rate : What is the rotation rate (in radians per second) of 17.0 inch diameter wheels on a vehicle traveling at 211 inches per second?
A block of wood floats in water with half : A block of wood floats in water with half its volume below the surface. The specific weight of the wood in lbf/ft3 units is about
Assume that the average life expectancy of a beagle : Assume that the average life expectancy of a Beagle is 13.3 years, and that 60% of Beagles lives to 12 to 15 years, and that their age follows normal distribution. Calculate the standard deviation of the distribution.
Turbine is proportional to the circular area swept : The average wind speed on the north Texas plains around Amarillo is approximately 6 m/s. An efficient wind turbine can convert 35% of the kinetic energy of the air (wind) into electrical energy at optimum conditions. If a turbine has blades 25 m in l..
Challenges facing all-electric vehicle transportation : One of the challenges facing all-electric vehicle transportation is the electrical infrastructure need to support rapid recharging of electric cars. Residential power circuits commonly supply alternating current (A/C) with maximum residential voltage..
Compression-ignition engine operates on ideal diesel cycle : A six-cylinder, four-stroke, 4.5-L compression-ignition engine operates on the ideal diesel cycle with a compression ratio of 17. The air is at 95 kPa and 55oC at the beginning of the compression process and the engine speed is 2000 rpm. The engine u..
Highest possible average flow velocity in the duct : A central heating system has a 60 W fan used to circulate air through the building ducts. A previous flow analysis showed that the fan needs to raise the air pressure by 50 Pa to maintain proper flow through the ducts. The fan is located in a horizon..
Piston-cylinder device-determine the final energy of system : A vertically mounted piston-cylinder device contains 1.5 kg of water and is being heated over a coal burning stove. During the process, 75 kJ of heat is transferred to the water and heat losses from the side walls amount to 9 kJ.
Carbon diffuses in iron via an interstitial mechanism : Carbon diffuses in iron via an interstitial mechanism—for FCC iron from one octahedral site to an adjacent one. In Section 4.3 (Figure 4.3a), we note that two general sets of point coordinates for this site are 0 ½ 1 and ½ ½ ½ . Specify the family of..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Specifications call for a composite part to be made of

specifications call for a composite part to be made of kevlar 49 fibers in a matrix of epoxy e0.65 . if the fiber

  Determine the overall efficiency of the pump-motor unit

water is pump from a lake to a storage tank at 18m above at a rate of 70 L/s while consuming 20.4 kW of electric power. disregarding any frictional losses in the pipes and any change s in kinetic energy, determine (a) the overall efficiency of the..

  Determine the rate of entropy generation of the steam

steam enters an adiabatic turbine at 8 mpa and 520 degc with a volumetric flow rate of 0.8 m3s and exits at 30 kpa. the

  Calculate the percentage volume change that would occur if

calculate the percentage volume change that would occur if a material were to be transformed from fcc to bcc. assume

  For a relaxed normal eye assume a viewing distance of 250

a microscope has a 2.40-cm focal length eyepiece and a 0.810-cm objective lens. for a relaxed normal eye assume a

  A torque t is imposed at the ends the maximum shearing

the composite shaft consists of three sections 1 a solid brass core 2 a middle steel tube and 3 an outer aluminum tube.

  The revenue per system is estimated to be 70000 in year 1

johnson implants is planning a new online patient diagnostics for surgeons while they operate. the new system will cost

  Plot the step response of the system at each value of t to

using matlab simulink set up the negative feedback system of nbspand find the value of the gainnbspaplot the step

  What is the fuel to air ratio and air flow rate

A 380 cc single-cylinder two-stroke motorcycle engine is operating at 5500 rpm. The engine has a bore of 82 mm and a stroke of 72 mm. Performance testing gives a bmep od 6.81 bar, bsfc of 0.49 kg/kW hr, and delivery ratio of 0.748. a) What is the fue..

  Determine the velocity of the ball at the points of the

a child throws a ball from point a with an initial velocity v 20 ms at an angle of 25 degrees with the horizontal.

  Air is now added to the accumulator until the volume is 1

a pneumatic accumulator arranged to maintain a constant pressure as air enters3 or leaves it is set for 200 psia.

  The boiler is sized to provide a steam flow of 50 kgs

a simple ideal rankine cycle with water as the working fluid operates between the pressure limits of 3 mpa in the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd