Certain power station produces an electrical output

Assignment Help Mechanical Engineering
Reference no: EM13718121

A certain power station produces an electrical output of 700 MW, operating at 42% efficiency. This plant uses a closed-circuit "dry" cooling system in which heat is expelled by cycling the cooling water through pipes which are in direct contact with air taken in from outside the plant. The fuel for the plant is lignite, which has a typical energy content of 15 MJ/kg.

a) What is the mass of lignite consumed in 1.00 hour of operation of the plant?

b) If the cooling water operates between a temperature of 90°C and a temperature of 30 °C, what mass of water must be cycled through the cooling system in 1.00 hour?

Reference no: EM13718121

Questions Cloud

Heat engine operating on the carnot cycle : A heat engine operating on the Carnot cycle has an efficiency of 65%. The waste heat from the cycle is rejected to the atmosphere at 20 deg. C. at a rate of 250 kW. What is the temperature of the heat source driving the engine in deg. C? For the heat..
Magnitude of the support reaction on the left end of beam : A 20ft long beam has a support reaction at each end and a 12ft long uniformly distributed load of 20lb/ft starting on the left edge. The uniformly distributed load is modeled as a normal concentrated load of how many pounds?
Closed piston-cylinder arrangement : One half of a mole of air is taken through the following processes in a closed piston-cylinder arrangement. From the initial state (V1 = 10 L, p1 = 1 atm) the gas is expanded at constant pressure to a volume of 20 L. It is then heated at constant vol..
Find that she cannot move either leg. advise aurelie : Explain how the common law and statutory rules of interpretation could be applied to the situations - Winnie is caught by a security guard as she is licking white aspirin powder.
Certain power station produces an electrical output : A certain power station produces an electrical output of 700 MW, operating at 42% efficiency. This plant uses a closed-circuit "dry" cooling system in which heat is expelled by cycling the cooling water through pipes which are in direct contact with ..
Construct an e-r diagram for a car insurance company : Construct an E-R diagram for a car insurance company that has a set of customers,each of whom owns one or more cars. Each car has associated with it zero to any number of recorded accidents
Design a table or matrix to perform : Design a table or matrix to perform your evaluation comparison. The evaluation criteria should include quality objectives and organizational capabilities and considerations, and should use some type of weighted priority scheme for ranking.
Identifying networking needs : 1. Assess the current network EA, identifying networking needs. 2. Analyze changes that are needed to the network EA for requirements and technology upgrades. 3. Include these changes into viewpoints to create the network "To-Be" EA
Find the value of n to determine optimal order quantity : Find the value of n to determine optimal order quantity

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd