Carbon-containing gas diffuses under surface of steel shaft

Assignment Help Mechanical Engineering
Reference no: EM13711717

1) A 5mm thick sheet of palladium with a cross sectional area of 0.2m^2 is used as a steady-state diffusion membrane in order to purify H2.The H2 concentration on the high pressure side of the sheet (i.e., the impure H2) is 1.5kg/m3 and that at the low pressure side is 0.3kg/m3. The diffusion coefficient for H2 in palladium is 1x10^-8m2/s. Assume a linear concentration profile within the plate. Calculate the mass of H2 being purified per hour.

2) If a (carburizing) carbon-containing gas diffuses under the surface of a steel shaft, the concentration of carbon under the surface will increase with time as the process proceeds. The steel shaft initially has a carbon content of 0.2wt%. Calculate the time, in minutes, necessary to increase the carbon content to 0.4wt%, at a distance of ½mm below the surface. The temperature is 1700°F. The carbon content at the surface is 0.892wt%. The diffusion coefficient at 1700°F is 1.28×10^-11m2/s.

Reference no: EM13711717

Questions Cloud

Determine coefficient of performance for this refrigerator : Consider a refrigerator that accepts 15 kW of heat in the evaporator and rejects 19.76 kW of heat from the condenser. The compressor requires an input of 5 kW of power and loses 0.24 kW of heat. Determine the coefficient of performance for this refri..
How far apart are the minima : If one shines a laser with wavelength λ = 650 nm through a single slit of width a = 0.04 mm, How far apart are the minima
Determine the gravitational potential energy : Determine the gravitational potential energy, in kJ, of 2 m3 of liquid water at an elevation of 30 m above the surface of Earth
Brayton cycle refrigeration system uses air as working fluid : A reverse Brayton cycle refrigeration system uses air as the working fluid. The turbine and compressor operate ideally, and regeneration (recuperation) is used in the cycle. The pressure ratio is 5. Air enters the compressor at 12.5 psia, 70°F. After..
Carbon-containing gas diffuses under surface of steel shaft : A 5mm thick sheet of palladium with a cross sectional area of 0.2m^2 is used as a steady-state diffusion membrane in order to purify H2.The H2 concentration on the high pressure side of the sheet (i.e., the impure H2) is 1.5kg/m3 and that at the low ..
What is difference between business and systems integration : Explain why it is important for managers at all levels to be involved with decisions regarding the use and implementation of information system.
Evaluate the shortest distance in which car can stop safely : A car has a mass of 1500 kg. If the driver applies the brakes while on a gravel road, What is the shortest distance in which the car can stop safely
Evaluate what is the tension in the rope : You swing an object in a vertical circle of radius 0.900m. What is the tension in the rope
What is the mass flow rate of steam through the diffuser : Steam at a pressure of 14.7psia and a temperature of 320deg F enters a diffuser inlet at a velocity of 500ft/s. The steam decelerates in the diffuser to a velocity of 100ft/s. The steam leaves the diffuser as saturated vapor at 240 deg F. The area of..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd