Carbon annealed steel rod has a rectangular cross section

Assignment Help Mechanical Engineering
Reference no: EM13704005

The company has been asked to assess the effects of a variety of engineering conditions on a selection of components, perform calculations for the components that follow.

A. A medium carbon annealed steel rod has a rectangular cross section and must cope with a tension of 3 tones, the thickness of the rod is 15mm, calculate the size of the cross section.

B. Calculate the tensile stress in a rod 40mm in diameter with a load of 200kN.

C. Calculate the diameter of a medium carbon steel pin in double shear subjected to a suddenly applied shearing force of 150000 N.

Reference no: EM13704005

Questions Cloud

No change compared to the actual valve : Using an Erlenmeyer flask with 2ml of water instead of 50ml, would it make the experimental molarity higher, lower or no change compared to the actual valve?
Total heat flow through the copper-fiberglass combination : One side of a copper block 5 cm thick is maintained at 250*C. The other side is covered with a layer of fiberglass 2.5 cm thick. the outside of the fiberglass is maintained at 35*C, & the total heat flow through the copper-fiberglass combination is 5..
Diameter sphere is heated to a temperature : A 4.0 cm diameter sphere is heated to a temperature of 200 C & is enclosed in a large room at 20 C. Calculate the radiant heat loss if the surface emissivity is 0.6.
What is the temperature change of the water : Liquid water at 26.67°C flows in a straight horizontal pipe in which there is no exchange of either heat or work with the surroundings. Its velocity is 40 ft/seg in a pipe with an internal diameter of 2.54 cm until it flows into a section where the p..
Carbon annealed steel rod has a rectangular cross section : The company has been asked to assess the effects of a variety of engineering conditions on a selection of components, perform calculations for the components that follow. A medium carbon annealed steel rod has a rectangular cross section and must cop..
What will the total pressure become : A 9.75-L container holds a mixture of two gases at 45 °C. The partial pressures of gas A and gas B, respectively, are 0.186 atm and 0.820 atm. If 0.190 mol of a third gas is added with no change in volume or temperature, what will the total pr..
Hydrogen atoms replaced respectively with chlorine atoms : Methyl chloride, methylene chloride, chloroform, and carbon tetrachloride are all part of what group that has had one, two, three, or four hydrogen atoms replaced respectively with chlorine atoms?
Did the biker go uphill or downhill : Many bike computers tell the ride what altitude they are at and how the altitude is changing using a basic barometer and pressure differences. A biker rides on a hill and the computer reads barometric pressures of 475 mm Hg at the start and 530 mm Hg..
What is the balanced equation : If 2.0 grams of calcium chloride react with 3.5 grams of sodium hydroxide in a double replacement what is the balanced equation

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd