Capacity and level of service profile of the facility

Assignment Help Mechanical Engineering
Reference no: EM13871110

Question 1: Traffic on an approach of a signalized intersection is travelling at 60 km/h with a density of 50 km/km/In. The duration of the red signals indication for this approach is 30 Sec.

If the saturation flow is 1950veh/h/In with a density of 52 veh/km/In and a jam density is 125veh/km/In, determine the following

a. The length of the queue at the end of the red phase

b. The maximum queue length

c. The time it takes for the queue to dissipate after the end of the red indication

Problem 2: An Australian freeway directional facility 5.5 km in length (Figure Q2) is known to be operating under capacity but the traffic is expected to grow in future. The existing conditions are as follows:

a. The section characteristic are shown in table

b. The acceleration and deceleration rate 100m long

c. Each ramp has one lane

d. The traffic demand profile are shown in table

e. Each time interval is 15 min. and all the demands are expressed as hourly flow rate during each time interval

What is the capacity and level of service profile of the facility under the existing condition?

1826_capacity and level of service profile.jpg

1025_Table 1.jpg

2178_Table 2.jpg

Reference no: EM13871110

Questions Cloud

Different forms of entity including the sole proprietorship : compare and contrast the different forms of entity including the sole proprietorship
Why is depreciation recorded as an expense : Why is depreciation recorded as an expense in proprietary funds, but not as an expenditure in government type funds?
Determine the volume of water lost : Determine the volume of water lost (in m3) through evaporation during a year from Lake Okeechobee (Florida). Lake Okeechobee has a surface area of 190,000-ha located in a region where the annual rainfall is 1500 mm. The increase in the depth of th..
When should an internal service fund be used : When should an Internal Service Fund be used?
Capacity and level of service profile of the facility : What is the capacity and level of service profile of the facility under the existing condition?
Discuss some of the drawbacks of morbidity indicators : Discuss some of the drawbacks of morbidity indicators. In what ways do investments in health contribute to economic development?
The revenues and the expenses of a proprietary fund : What is the cause and effect relationship between the revenues and the expenses of a proprietary fund?
Discuss the non-economic functions of education : Discuss the non-economic functions of education. Give an overview of human capital theory. Explain the role of productivity in this theory.
The impact of apns on the quality of healthcare : This report should contain the following sections: Executive Summary, Introduction and Background, Economic Impact of APNs on the Healthcare Delivery System and The Impact of APNs on the Quality of Healthcare

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd