Calculated the work and heat transfer during the process

Assignment Help Civil Engineering
Reference no: EM13307660

HElium is contained in a closed cylinder fitted tightly with a piston. The initial conditions of the helium are 7 ft^3, 80 psia, and 100 F. The helium expands reversibly according to process PV^1.5=C until the pressure reaches 15 pisa. Calculated the work (Btu) & heat transfer (Btu) during the process. Assume that helium is an ideal gas.

Reference no: EM13307660

Questions Cloud

Analyze the case on the speed team at ibm : Analyze the case on The Speed Team at IBM
Case study on usability of ipads and websites : The following report must be used for reference to complete this assignment. The Nielsen Norman Group published a report titled, "Usability of iPads and Websites." The report is a case study of the iPad usability
Determine what is the temperature in the tire after driving : The temperature when the tires were in flated was 25 F. Assuming no change in air mass or volume, what is the temperature (F) in the tire after driving yesterday is a pressure on 44 psig was measured
Calculate the new angular speed of the student : A student sits on a rotating stool holding two 2.0-kg objects. When his arms are extended horizontally, Find the new angular speed of the student
Calculated the work and heat transfer during the process : The initial conditions of the helium are 7 ft^3, 80 psia, and 100 F. The helium expands reversibly according to process PV^1.5=C until the pressure reaches 15 pisa.
Calculate the net work done by the gas in one cycle : In the process represented in the figure, 2.4 moles of an ideal monatomic gas start at state a, with pressure 1 atm (1.01*10^5 N/m^2), Find the net work done by the gas in one cycle
Determine the heat transfer and the work for the process : A cylinder fitted with a piston has a volume of 2ft^3 and contains 0.5 lbm of steam at 60 psia. Heat is tranferred to the stream until the temperatureis 500 F, while the pressure remains constant
What is the tension in each of the cables : A 15.0 kg loudspeaker is suspended 2.50 m below the ceiling by two 3.10m long cables that angle outward at equal angles
Black coalition for aids prevention : Critically analyse the recruitment challenges in the case study, including how they impact on the strategic issues mentioned in the case.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determining the pumping rate

Determine the required pumping rate. the aquifer has T= 1600 m 2 /day and the wells each have radius of influence of 600m.

  What is the probability that gas and oil will be short

A community has three major sources of power supply: electricity, gas and oil. Let E, G and O denote events of shortages of each of these power sources, respectively. Their probabilities are estimated to be 0.15, 0.10 and 0.20 respectively.

  What is maximum acceleration from rest for car with engine

The car weights 2450 lb, the mechanical efficiency of the drivetrain is 90%, and the wheel radius is 14 inches. The base engine develops 200 ft-lb of torque, and a modified version of the engine develops 240 ft-lb of torque.

  Define what must the drivers eye height in the van be

A civil engineering student contends that 60 mph is safe in a van because of the higher driver's eye height. If all other design inputs are standard, what must the driver's eye height in the van be for the student's claim to be valid

  Determine the outlet temperature of the engines compressor

The thermal efficiency of an aircraft gas turbine engine (turbojet, based on ideal Brayton cycle) is 25%. The aircraft travels at a speed 770 km/h at an altitude 6800 m above sea level (standard atmospheric air). The combustion chamber outlet temp..

  Determine the chemical oxygen demand cod of a mixture

Determine the chemical oxygen demand (COD) of a mixture of 250 mg/l glutamic acid (C5H10N2O3) and 200 mg/l of glucose(C6H12O6).

  Draw the bending moment and shear force diagrams

Draw the Bending Moment and Shear Force diagrams for the girder and calculate the maximum tension in the cable.

  Determine what is the rovers weight on the surface of mars

When the Mars Exploration Rover was fully assembled, its mass was 180 kg. The acceleration due to gravity at the surface of Mars is 3.68 m/s2. a) What was the rover's weight when it was at sea level on Earth

  Estimate the pressure change over 80 m of pipeline

Water at 20ºC flows at a velocity of 2 m/s in a 200-mm diameter horizontal ductile-iron pipe. a) Estimate the friction factor in the pipe, and state whether the pipe is hydraulically smooth or rough.

  Calculate the heat and work excahnged during the process

a piston-and-cylinder device contains 5 kg of water initially at 150 C and 0.20 MPa. The frictionless piston is then pushed slowly in an isothermal process until the volume of water becomes 10% of its initial value.

  What is the minimum tractive effort required for vehicle

A 3000 lb vehicle has a drag coefficient of 0.32 and a frontal area of 30 ft2. What is the minimum tractive effort required for this vehicle to maintain a 65 mph speed on a 2% upgrade through an air density of 0.002045 slugs/ft3

  Crash at a railroad crossing

Due to a crash at a railroad crossing, an overpass is to be constructed on an existing level highway. the existing highway has a design speed of 50 mi/h.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd