Calculate what is the force required at a constant rate

Assignment Help Civil Engineering
Reference no: EM13315196

A 20-kg iron ball is moving at 100 km/hr should be accelerated at a constant rate of 10 m/(sec)^2. What is the force required

Reference no: EM13315196

Questions Cloud

Find the piston mass that will create a pressure inside : A vertical hydraulic cylinder has a 150-mm diatomic piston with hydraulic fluid inside the cylinder and an ambient pressure of 1 bar. Assuming standard gravity, find the piston mass that will create a pressure inside of 1250kPa.
What is the final speed of the block : A small block of mass 0.97 kg slides without friction on a horizontal table. Initially it moves in a circle of radius R0 = 0.52 m with a speed 1.3 m/s. What is the final speed of the block
Determine what is the acceleration of diatomic oxygen gas : 2 kilomoles of diatomic oxygen gas are enclosed in a 10-kg steel container. A force of 2kN now accelerates this system. What is the acceleration
What does the slope of the linear line : A graph of the Force applied to a spring and the distance it stretches F vs. x yields some valuable information. What does the slope of the linear line
Calculate what is the force required at a constant rate : A 20-kg iron ball is moving at 100 km/hr should be accelerated at a constant rate of 10 m/(sec)^2. What is the force required
Hat is the direction of the net electrical field : Consider two particles, each with a charge of +Q located at the opposite corners of a square of side d. What is the direction of the net electrical field at point P
Determine the average normal stress at the critical section : two 10 mm thick steel plates are fastened together by means of two 20mm bolts that fit tightly into the holes. if the joint transmits a tensile force of 45 kn determine the average normal stress in the plates at a section where no holes occur
How to decrement the ttl field of the packet : In addition to the above-mentioned  KeyboardInterrupt (used to terminate the program), you will need to handle any I/O-related exceptions.
Determine the magnitude and location of the resultant force : The tank contains water to depth of 2m and oil (SG=0.8) on top of the water to a depth of 1m. Determine the magnitude and location of the resultant force acting on one end of the tank (i.e. 3m high by 3m wide).

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the shear modulus for the aluminum

The elastic portion of the tension stress-strain diagram for an aluminum alloy. The specimen used for the test has a gauge length of 2 in and a diameter of 0.5 in. When the applied load is 9 kips, the new diameter of the specimen is 0.49935 in.

  Determine what would the population be in 25 years

Nairobi has a birth rate of 3.3 individuals per individual per year and a death rate of 3.2 individuals per individual per year. If the carrying capacity were 105, what would the population be in 25 years

  How many days will fish hatchery have to contain river water

If the initial concentration of parathion in the runoff from the agricultural field is 3 ppb, the velocity of the river is 2.3 miles/day, how many days will the fish hatchery have to contain river water in holding tanks until the parathion concent..

  Determine the secondary sludge produced per day per pound

a low rate trickling filter plant gives 95% BOD5 removal. the primary clarifier removes 33% of the BOD5 applied to it. the secondary sludge amounts to 0.029lb dry solid/cap-day. if the raw wastewater has a BOD5 of 0.17lb/cap-day.

  What are the total heads given by piezometers b and c

The total heads given by piezometers A and D are 98.9 cm and 3.6 cm, respectively. What are the total heads given by piezometers B and C?

  Determine distance the officer traveled before overtaking

The officer believes the driver is intoxicated and begins accelerating uniformly to 50 mi/h in 8 seconds and maintains a constant velocity of 60 mi/hr, overtakes the motorist 42 seconds after he passed the officer.

  Determine how much butane would be needed to burn

You have a contaminated air stream containing 1000 ppmV of toluene and you decided to incinerate to a DRE of 99.9%. You are using butane as fuel to reach the temperature and consider the lean toluene has no heating value.

  Define flow at a hydraulic jump in terms of flow

Define flow at a hydraulic jump (upstream and downstream) in terms of the types of flow and corresponding Froude number. What is the depth of water at each section (upstream and downstream) compared to critical depth

  Determine the length of the swale required with side slopes

The longitudinal slope of the swale is to be 1.5% with side slopes of 5:1 (H:V). If the grassed swale has a Manning's n of 0.030 and a minimum infiltration rate of 200 mm/hr, determine the length of the swale required.

  Calculate the fuel load density and the opening factor

A hotel room has a floor area of 10 m by 4 m and is 2.5 high and has a window which is 1.6 m high and 3 m wide. The room contains some furniture and other commodities containing 50 kg polyurethane with 25 MJ/kg and 350 kg wood with 18 MJ/kg.

  Determine the mass nd specific volume of argon gas in vessel

Determine the mass and specific volume of argon gas in a vessel at 150 kPa and 20°C. The vessel is spherical, with radius 5 m.

  Determine number of kilograms of chlorine needed per day

Consider again the proposed water treatment plant for a city of 100,000 people where the maximum daily water usage rate is 99 X 106 L/d. Determine (a) the number of kilograms of chlorine needed per day and (b) the capacity of the contact tank.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd