Calculate wall thickness required

Assignment Help Mechanical Engineering
Reference no: EM131382505

1. A cast-iron pipe, 3 ft in diameter, is subjected to an internal gage pressure of 100 psi. Calculate the wall thickness required if the allowable tensile stress is 11,000 psi.

2. A steel pipe located in a hydroelectric power plant is 24 in. in diameter and has a wall thickness of 3 8 in. The system operates under a maximum head of 750 ft. Assuming an ultimate tensile strength of 55,000 psi, calculate the factor of safety for the pipe.

Reference no: EM131382505

Questions Cloud

Construct a strategic plan for an organization : What is the best way to construct a strategic plan for an organization? 200 words please
Calculate the required wall thickness : A closed cylindrical air-compressor tank is 600 mm in diameter and is subjected to an internal pressure of 5 MPa. The tank walls are of steel, which has an allowable tensile stress of 110 MPa. Calculate the required wall thickness.
What state laws protect owners of intellectual property : What federal or state laws protect owners of intellectual property? How do they apply here? Explain. What damages, if any, has Mathis suffered because of Normandale's conduct? Explain.
How will you communicate the companies : Students please answer the following questions: How will you communicate the companies' goals and values without being authoritarian? What steps will you take to break down the barriers between:
Calculate wall thickness required : A cast-iron pipe, 3 ft in diameter, is subjected to an internal gage pressure of 100 psi. Calculate the wall thickness required if the allowable tensile stress is 11,000 psi.
Does your firm have a clear internet strategy : Does your firm have a clear internet strategy? If yes, how would you describe the effort in terms of reach, richness and affiliation? Is that a value adding strength or a value diminishing weakness? If not, what advice would you offer about the ..
Create a business plan for a forclosure clean up : Business Plan- Create a Business Plan for a forclosure clean up and property preservation business. https://www.youtube.com/watch?v=z5CHWO1EkC0&t=435s
Prevention and management of tropical diseases : Consider primary health care approaches and how the approaches might contribute to the prevention and management of tropical diseases
Process impact the outcome of the event : Think about the last event you had to plan for either at work or in your personal life. Did you have a process? How did having or not having a process impact the outcome of the event?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The device is then heated until the temperature is 100 c

319 grams of r-134a initially fill a weighted piston-cylinder device at 60 kpa and -20 c. the device is then heated

  Insulated reactor operating at steady state-burns completely

Methane gas (CH4) at 25° C, 1 atm enters an insulated reactor operating at steady state and burns completely with  x % of theoretical air entering at 25°C, 1 atm. Calculate the adiabatic flame temperature (AFT) at x=100, 200, 300 and 400 % and plot t..

  Draw the shear-force and bending-moment diagrams for beam

The simple beam AB shown in the figure is subjected to a concentrated load P and a clockwise couple M1= PL/3 acting at the third points. Draw the shear-force and bending-moment diagrams for this beam.

  Determine the specific volume of superheated water vapor at

determine the specific volume of superheated water vapor at 15mpa and 350oc using a the ideal gas equation b the

  Determine the increase in velocity required at a

When the spacecraft reaches point B on the elliptical transfer orbit, its speed B v is increased to the orbital speed of Mars. Knowing that the mass of the sun is 332.8 A? 103 times the mass of the earth, determine the increase in velocity requir..

  If the furnace is at 1200 degc and the surrounding room is

a 200 mm diameter sight window on the wall of a furnace is losing heat at a rate of 1500 w. if the furnace is at 1200

  What is the total filtration time required

The filter ofProb. 30.7 is operated at a constant rate of 0.6 gal/ft2-min from the start of the run until the pressure drop reaches 70 lb f/in. 2 and then at a constant pressure drop of 70IbJ/in.' until a total of 1400 gal of filtrate is obtai..

  Design a solid-straight centrally loaded column

Design a solid, straight centrally loaded column to carry 100,000 lbs. Assume one end is pinned and the other is fixed.

  Determine the velocity of the refrigerant

Refrigerant 134a exits a heat exchanger through .75-in - diameter tubing with a mass flow rate of .9 lb/s. The temperature and quality of the refrigerant are -15 Fahrenheit and .05, respectively. Determine the velocity of the refrigerant, in m/s.

  Operator of a pumper-tanker fire engine

1. How does the operator of a pumper-tanker fire engine control water flow to all the hoses in use? 2. For air flowing through a converging-diverging channel, sketch the variation of the air pressure as air accelerates in the converging section and..

  Find the total heat loss per m length of the steam line

find the total heat loss per m length of the steam line. Find also the temperature at the interface of steam and insulation.

  Calculate the thickness of a nickel foil that was found

Calculate the thickness of a nickel foil that was found to transmit 47.8% of the incident power of a beam of Cu Ka radiation. The density of Ni is 8.90 g/cm3.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd