Calculate thermistor temperature sensitivity for a

Assignment Help Mechanical Engineering
Reference no: EM13612828

(a) A thermopile consisting of 5 junction pairs of chromel-constantan is used to measure a temperature difference of 50oC with the cold junction at 25oC. Determine the voltage output of the thermopile. What is its sensitivity?

Given E25 = 1.495 mV and E75 = 4.657

(b) Calculate thermistor temperature sensitivity for a thermistor at 100oC. Thermistor Resistance at 100oC is 100 ohms. Take Beta = 4120 k @ 100oC. (hint: Use the thermistor resistance temperature relation, R =Ro exp {Beta((1/T)-(1/To))}.

Reference no: EM13612828

Questions Cloud

This sample of 40 has a mean value of x-bar which belongs : the local bakery bakes more than a thousand 1-pound loaves of bread daily and the weights of these loaves vary. the
A piece of nichrome wire has a radius of 72 x 10-4 m it is : a piece of nichrome wire has a radius of 7.2 x 10-4 m. it is used in a laboratory to make a heater that dissipates
Estimate the indicated probability by using the normal : estimate the indicated probability by using the normal distribution as an approximation to the binomial distribution. a
On january 1 2010 lester company purchased 70 of stork : on january 1 2010 lester company purchased 70 of stork corporations 5 par common stock for 600000. the book value of
Calculate thermistor temperature sensitivity for a : a a thermopile consisting of 5 junction pairs of chromel-constantan is used to measure a temperature difference of 50oc
There are approximately 109 million tvs in the united : there are approximately 109 million tvs in the united states. each uses on average 74 w of power and is turned on for
Your group doesnt have an established beta value for this : suppose you work for an automotive engineering group that is responsible for modeling the length of life of brake
The dielectric constant of this substance is 593 find the : an initially uncharged air-filled capacitor is connected to a 3.39-v charging source. as a result 9.57 times 10-5 c of
Determine the ratio of the energy used by the blow-dryer in : a blow-dryer and a vacuum cleaner each operate with a voltage of 120 v. the current rating of the blow-dryer is 11 a

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the amplitude and phase when a force f 2cos3t

a weight attached to a spring of stiffness 525 nm has a viscous damping device. when the weight is displaced and

  Determine the number of revolutions

Determine the number of revolutions that the motor executes in a) reaching its rated speed, b) coasting to rest.

  A car moves along a straight line starting from rest with

a car moves along a straight line starting from rest with an acceleration of 5 fts2 for 6 seconds then brakes with a

  Knowing that the tension in member b is 6kn and that the

two structural members b and c are bolted to the bracket a. knowing that the tension in member b is 6kn and that the

  Determine the rate of heat transfer to the mid-stage

Determine the rate of heat transfer to the mid-stage cold head and determine the rate of heat transfer to the cold head

  Calculate the overall efficiency the heat rate mw and the

calculate the overall efficiency the heat rate mw and the total fuel rate kgs of a combined-cycle power plant 1 if no

  Determine isentropic efficiency of the compressor

Carbon dioxide enters an adiabatic compressor at 100kPa and 300K at a rate of 0.5kg/s and exits at 600kPa and 450K. Considering constant specific heat, determine (a) isentropic efficiency of the compressor (b) the rate of entropy change in (kW/K) ..

  The manometer shown above in problem 1 above contains water

the manometer shown above in problem 1 above contains water and kerosene. with both tubes open to the atmosphere the

  Estimate the torque required at the base of a flag pole

Estimate the torque required at the base of a flag pole to hold it in place in a 30mph wind. Assume the flag pole is a vertical cylinder with D=10cm and L=10m, and assume the wind drag force is uniform along the pole.

  Calculate the actual power transmitted to the second pulley

Calculate the actual power transmitted to the second pulley and calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.

  Are there alternative solutions which might also effective

how can this goal be achieved? are there alternative solutions which might also be effective?

  The isentropic efficiencies for the turbine and pump are 85

a cycle based on a rankine cycle with water as the work fluid must have its highest cycle pressure and temperature at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd