Calculate thermal efficiency of the power plant what is

Assignment Help Mechanical Engineering
Reference no: EM13633254

Steam enters the turbine in a vapor power plant at 1600 psia and 1000 degrees F (State 1) and expands to a pressure of 1 psia (State 2); isentropic efficiency of the turbine is 85%. Saturated liquid water (State 3) exits the condenser and is pumped back to 1600 psia (State 4); isentropic efficiency of the pump is 70%. The power plant produces a net power of 125 MW. The cooling water flowing through the condenser experiences a temperature increase of 12 degrees F.

(a) Calculate thermal efficiency (%) of the power plant.
(b) What is the mass flow rate (lbm/hr) of steam through the power plant?
(c) Calculate the mass flow rate (lbm/hr) of cooling water.
(d) Find the entropy generation (Btu/lbm-R) for the turbine and pump.
(e) Show the cycle on T-s diagram. Label states, show property values, and indicate appropriate lines of constant pressure.

Reference no: EM13633254

Questions Cloud

What was the speed of the car before impact assuming no : an automobile having a mass of 1000 kg is driven into a brick wall in a safety test. the bumper behaves like a spring
Suppose the claimed drying time is true that is 45 : a paint company claims their paint will be completely dry within 45 minutes after application. recently customers have
A what is the potential energy stored in the two bands : a slingshot consists of a light leather cup containing a stone. the cup is pulled back against two parallel rubber
The resulting life data from the batteries had a mean of : a popular flashlight that uses d size batteries was selected and severa of the same models were purchased to test the
Calculate thermal efficiency of the power plant what is : steam enters the turbine in a vapor power plant at 1600 psia and 1000 degrees f state 1 and expands to a pressure of 1
A spring is hung from a ceiling and an object attached to : a spring is hung from a ceiling and an object attached to its lower end stretches the spring by a distance of 5.00 cm
The air in a bicycle tire is bubbled through water : the air in a bicycle tire is bubbled through water andcollected at 25 degrees celsius. if the total volume of gas
A random sample of 70 needles was taken from a medical : a random sample of 70 needles was taken from a medical manufacturing facility and 24 were found to be defective.
A wooden cylinder 300cm high floats vertically in a tub : according to archimedes principle the mass of a floating objectequals the mass of the fluid displaced by the object.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd