Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Let E = yax V/m at a certain instant of time, and calculate the work required to move a 3-C charge from (1,3,5) to (2,0,3) along the straight-line segments joining:a) (1,3,5) to (2,3,5) to (2,0,5) to (2,0,3)b) (1,3,5) to (1,3,3) to (1,0,3) to (2,0,3)Note: answers should be a) -9 J, b) 0
Given an ideal op amp to implement designs for the following closed-loop gains, what values of resistors (R1,R2) should be used. Where possible, use at least one 10-kohm resistor as the smallest resistor in your design.
A 2722-kg weight is being pushed up an inclined surface at constant speed by a cylinder. The coefficient of friction between the weight and inclined surface equals 0.15. for a pressure of 6.9 MPa, determine the required cylinder diameter.
A four pole DC machine has a wave winding of 300 turns. The flux per pole is .025 webers. The DC machine rotates at 1000 RPM. Determine the generated voltage and the kW rating if the current through the turn is 25 amps.
A resistive temperature sensor is modeled as R(T) = 100 +0.0039(T-25)+1.0x10^-5(T-25)^2 where T is in degrees C. Calculate the tempco and sensitivity at T = 50 degrees C.
Assume CMOS inverter propogation delay is 100 pico seconds. Design a one input/ one output pulse generating circuit which will generate 600 pico seconds wide pulse at the output each time the input changes from one logic to another.
A three-phase fault occurs at the generator terminals causing the angle of part (c) to increase. The fault is subsequently cleared. Find the maximum value that this angle can reach during the fault (i.e. the critical clearing angle) so that the ge..
(b) Construct a 3-input-8-output binary decoder using NOT, AND and OR gates (without enable logic). (c) Using the above decoder, design the following logic function. Add the required gates and re-draw the decoder.
Assume that we make an enhancement to a computer that improves some mode of execution by a factor of 10. Enhanced mode is used 50% of the time, measured as a fraction of the execution time when the enhanced mode is in use.
Water is flowing through a 0.1 m diameter pipe at a velocity of 2.5 m/s. what diameter pipe will it need to transition into to decelerate to 0.5 m/s
The speed of a 10HP, 230V, 1200 rpm separately excited DC motor is controlled by a 1-phase full-wave bridge converter. The rated armature current of the motor is 10 A. The armature resistance is 0.25 Ohm and the armature inductance is 10 mH.
A block of copper has a volume of 5.5x10-3 m3 and a mass of 50.0 kg. The specific heat capacity of copper is 385 J/(kgC0). The melting point of copper is 1085 0C. The latent heat of fusion is Lf = 2.05x105 J/kg. The coefficient of volume thermal e..
A capacitor is formed by two metal parallel plates with the dimensions 210 mm x 210 mm separated by the gap of 1.2 um (u=micro) filled with dielectric material with relative dielectric permittivity 3.8.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd