Calculate the weight percent austenite and weight

Assignment Help Civil Engineering
Reference no: EM13560308

1.A .90% Carbon hypereutectoid plain carbon steel is slowly cooled from 900 degrees C to just slighty above 723 degrees C calculate the weight percent proeutectoid cementite and weight percent austenite present in the steel

2.A .65% Carbon hypoeutectoid plain carbon steel is slowly cooled from 950 degrees C to just slighty above 723 degrees C calculate the weight percent austenite and weight proeutectoid ferrite in this steel.

Reference no: EM13560308

Questions Cloud

Determine the mass concentration of carbon : A mild steel component in a form of a finite slab with a thickness of 2L=2.5 mm is to be hardened by packing it in a carbonaceous material in a furnace for a predetermined time
Discuss the three challenges that strategists face today : Discuss the three challenges that strategists face today
The situation of the conflict between bp and greenpeace : The situation of the conflict between BP and greenpeace
Make a preliminary selection of member size : The service loads on a steel truss member are PDL: 120 kips (tension), PLL =240 Kips (tension), PWL = 200 kips (tension/compression). Steel properties are Fy = 46 ksi, Fu = 58 Ksi. Using the tables in the AISC manual, make a preliminary selection of ..
Calculate the weight percent austenite and weight : A .90% Carbon hypereutectoid plain carbon steel is slowly cooled from 900 degrees C to just slighty above 723 degrees C calculate the weight percent proeutectoid cementite and weight percent austenite present in the steel.
What is the drawdown halfway between well a and well b : Two pumping wells, A and B, are 100m apart. They each completely penetrate a homogeneous, confined aquifer, and pump at exactly the same rate, 5m^3/day. Prior to pumping
Why bother target marketing : Q1. 'Why bother target marketing? By marketing my product to the entire market, I have a greater chance of success.' Discuss this statement by comparing the benefits of using targeting as opposed to not using it. Your discussion should demonstrate th..
Calculate the weight percent proeutectoid cementite present : A 1.10% Carbon hypoeutectoid plain carbon steel is slowly cooled from 900 degrees C to just slighty below 723 degrees C calculate the weight percent proeutectoid cementite present in this steel.
Organizing to implement cost leadership strategies : Organizing to implement cost leadership strategies

Reviews

Write a Review

Civil Engineering Questions & Answers

  An uncovered swimming pool loses 1 inch of water off

An uncovered swimming pool loses 1 inch of water off its 1,000ft^2 surface each week due to evaporation. the heat of vaporization for water at the pool temperature is 1,050 Btu/lb

  Can the new device be justified at a toll gate

Cars arrive at a toll gate on a freeway according to a Poisson distribution with mean 90 per hour. Average time for passing through the gate is 38 seconds. Drivers complain of the longwaiting time.

  Determine the acceleration of the rod

A rectangle commercial building must be laid out 200.00 ft wide and 300.00 ft long. if the steel tape used is 100.02 ft long under standard conditions, what distances would be laid out?.

  What is the concentration of nh3of household ammonia

What is the concentration of NH3 (in mg/L) of household ammonia that contains 3.00 percent by wieght of NH3. Assume the density of water = 1000kg/m^3

  Determine the gauge pressure head and the absolute pressure

A vertical tank of 4.sm2 cross-sectional area is filled with 13.5m3 of water, 9.0m3 0f a fluid with an s.G. of 3.2,6.75;. or oir with an s.G. of 0.85 and 0.9m3 of mercury with an s.G. of 13.s7.

  Calculate the time needed for the following particles

Assume that the current cost for a 120-pupil school constructed of wood frame for a city is $1,800,000. We are asked to develop an order-of-magnitude estimate for a 90-pupil school ?

  Determine the largest distance x that the stream can reach

A nozzle discharges a stream of water with an initial velocity v0 of 50 ft/s into the end of a horizontal pipe of inside diameter d=5ft. determine the largest distance x that the stream can reach.

  Calculate the minimum length of this curve

If the clearance is not adequate in this type of case what modification to L would be required to increase the clearance? Discuss possible ramifications of making this modification. (Do not need to do any calculations in part c).

  Determine pressure drop in length assuming laminar flow

Under these conditions flow is expected to be turbulent, but for a clean air, very smooth enterance (with guided vanes) to the tube and no tube vibration, it may be possible to maintain laminar flow.

  Calculate critical crack length required to cause fracture

We know that the part has an intial crack of length 0.02 mm, and that the fracture toughness is 55 MPA(m)^1/2If the part is subject to cycle loading of 300 Mpa in tension and compression, calculate (assuming Y1.2, n = 3.4 and C = 2x10^-11 in units ..

  Estimate its load carrying capacity assuming a safety factor

A 12 m-long and 800 mm-diameter drilled pier is constructed in a clayey soil with a1.5 m-diameter bell at the base. The top 7 m of the clay has an average Cu of 40 Kpa and the clay underneath has a Cu of 90 Kpa

  What is the departure rate when the queue reaches vehicles

The arrival rate at a parking lot is 6 veh/ min. Vehicles start arriving at 6: 00 P. M., and when the queue reaches 36 vehicles, service begins. If company policy is that total vehicle delay should be equal to 500 veh-min, what is the departure ra..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd