User Account

All Pages

Calculate the voltage at the burn out point

Assignment Help Mechanical Engineering
Reference no: EM13965452

A nickel wire carrying electric current of 1.5 mm diameter and 50 cm long, is submerged in a water bath which is open to atmospheric pressure.

Calculate the voltage at the burn out point, if at this point the wire carries a current of 200A.

Reference no: EM13965452

Questions Cloud

Problem regarding the assumption of independence : Suppose the lot consists of ten  boards,  of which two are green. Does the assumption of independence now yield approximately the cor- rect answer for P(A n B)? What is the critical difference between the situation here and that of part (a)?
Find the change in value of heat transfer coefficient : Assume the water to be at a pressure of 20 atm. And also find the change in value of heat transfer coefficient
What is the amount of under applied or overapplied overhead : What is the amount of under applied or overapplied overhead for the year?
Expression for the probability : a. Assuming that an item has a aw, what is the probability that it is detected by the end of the second  xation (once a  aw has been detected, the sequence of xations terminates)? b. Give an expression for the probability that a aw will be detecte..
Calculate the voltage at the burn out point : Calculate the voltage at the burn out point, if at this point the wire carries a current of 200A.
Calculate the temperature of the bottom surface of the pan : Assuming nucleate boiling conditions calculate the temperature of the bottom surface of the pan.
Find the magnitude and direction of c : Write each vector in terms of the unit vectors ^i and ^j. Use unit vectors to express the vector C, where C = 3.00A - 4.00B.
Age and change in systolic blood pressure : In order to study any possible relationship between age and change in systolic blood pressure (BP) (mm Hg) in 24 hours in response to a treatment, the following data were obtained from 11 individuals.
Estimate the rate of heat to be supplied to the plate : A thin 100 cm long and 10 cm wide horizontal plate is maintained at a uniform temperature of 150oC in a large tank full of water at 75oC.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd