Calculate the velocity v of the system after the boulder

Assignment Help Mechanical Engineering
Reference no: EM13640153

The 300 kg and 400 kg mine cars are rolling in opposite directions along the horizontal track with the respective speeds of 0.6 and 0.3 m/s. Upon impact the cars become coupled together. Just prior to impact, a 100 kg boulder leaves the delivery chute with a velocity of 1.2 m/s in the direction shown and lands in the 300 kg car. Calculate the velocity v of the system after the boulder has come to rest relative to the car. Would the velocity be the same if the cars were coupled before the boulder dropped?

Reference no: EM13640153

Questions Cloud

Calculate the power of the engine calculate the standard : if the standard deviations are obtained to be 4n-m and 5 rpm for torque-165 n-m and rotational speed-3000 rpm through a
The intensity at a distance of 6 m from a source that is : the intensity at a distance of 6 m from a source that is radiating equally in all directions is 6.0 x 10-10 wm2. what
A mass is attached to a vertical spring and bobs up and : a mass is attached to a vertical spring and bobs up and down between points a and b. where is the mass located when its
Kinetic and potential engergy effects can be ignored : hydrogen h2 at 77 c 4bar enters an insulated chamber at steady state where it mixes with nitrogen n2 entering as a
Calculate the velocity v of the system after the boulder : the 300 kg and 400 kg mine cars are rolling in opposite directions along the horizontal track with the respective
The frequency of a wave increases what happens to the : the frequency of a wave increases. what happens to the distance between successive crests if the speed remains
A physiological experiment was conducted to study the : a physiological experiment was conducted to study the effect of various factors on pulse rate. for one factor there
Consider melting 300 moles of material x at 100 atm : suppose a single component material x has a critical temperature of 350.0 k and critical pressure of 7.50 atm. the
Air enters a well-insulated nozzle with a pressure of 1000 : air enters a well-insulated nozzle with a pressure of 1000 kpa a temperature of 527degc and a velocity of 20 ms. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the temperature at the firebrick-kaolin interface

a furnace wall is composed of three layers 15 cm of firebrick k 1.5 wmk followed by 22.5 cm of kaolin insulation brick

  Wwhat is the anticipated load at which the speciment is

a bending test is used on an experimental cemented carbide material. based on previous testing of the material its

  Determine the static head efficiency required of the

in an automotive gas turbine the centrifugal compressor is driven at 40000 rpm by an axial turbine. the compressor

  Advanced stress analysis assignment

Advanced Stress Analysis Assignment

  Consider a carnot refrigeration cycle with a working fluid

consider a carnot refrigeration cycle with a working fluid of r-134a operating between temperatures of -10oc and 20oc.

  A 25 mm diameter uniform steel shaft is 600 mm long between

a 25 mm diameter uniform steel shaft is 600 mm long between bearings.a find the lowest critical speed of the shaftb if

  Calculate the length of the conveyor belt shown b calculate

the crate containing 40 bricks sits on a slopped conveyor belt which is used to raise the crate to the next level of

  Saturated liquid refrigerant r-134a at 1159 bar enters an

saturated liquid refrigerant r-134a at 11.59 bar enters an adiabatic throttling valve which drops the pressure to 4.00

  More heat is transferred to the air until the temperature

five kilograms of air at 300 k is contained in a vertical cylinder by a frictionless piston of a mass such that the

  A string is attached to the drum radius r of a spool radius

a string is attached to the drum radius r of a spool radius r as shown in side and end views here. a spool is device

  A 250-kg crate b is suspended from a cable attached to a

a 250-kg crate b is suspended from a cable attached to a 20-kg trolley a which rides on an inclined i-beam as shown.

  Roast can be considered as a spherical shape and it is

a 5-lb roast initial at 70degf is placed in an oven at 350degf. you may assume the heat transfer coefficient is 2.5

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd