User Account

All Pages

Calculate the values of poisson ratio for the material

Assignment Help Mechanical Engineering
Reference no: EM131123015

A bar of mild steel 25 mm diameter twists 2 degrees in a length of 250 mm under a torque of 430 N m. The same bar deflects 0.8 mm when simply supported at each end horizontally over a span of 500 mm and loaded at the centre of the span with a vertical load of 1.2 kN. Calculate the values of E, G, K and Poisson's ratio v for the material.

Reference no: EM131123015

Questions Cloud

Evaluate the historical performance of the company : 1. Prepare four line graphs with the ratio on the vertical axis and the years on the hori- zontal axis for the following four ratios (rounded to one decimal place):
Discuss four exemptions and explain reasons why they exist : Discuss four exemptions and explain reasons why they exist. Then further discuss whether those communications should continue to be granted such a privilege; if you agree support your position, if you disagree, do likewise.
Determine the maximum stress set up due to compressive load : Assuming that, before loading, there is an initial sinusoidal curvature of the strut with a maximum deflection of 5 mm, determine the maximum stress set up due to a compressive end load of 200 kN. E = 208 GN/m2
Calculate the torque which can be transmitted by the tube : A steel tube has a mean diameter of 100mm and a thickness of 3 mm. Calculate the torque which can be transmitted by the tube with a factor of safety of 2.25 if the criterion of failure is maximum shear stress
Calculate the values of poisson ratio for the material : A bar of mild steel 25 mm diameter twists 2 degrees in a length of 250 mm under a torque of 430 N m. Calculate the values of E, G, K and Poisson's ratio v for the material
Determine the value of the shear stress : If the greater principal stress is limited to 100MN/mZ tensile, determine: the value of the shear stress; and the other principal stress
What is the firm total cost based upon the eoq : Vergas Enterprises wishes to determine the economic order quantity (EOQ) for a critical and expensive inventory item that it uses in large amounts at a relatively constant rate throughout the year. What is the firm's total cost based upon the EOQ c..
Determine the current weighted average cost of capital : Cascade Water Company (CWC) currently has 30 000 shares of common stock outstanding, trading at a price of R42 per share. Determine the current weighted average cost of capital for CWC
A network topology design for abc : For this project, you will design the layout of users, domains, trusted domains, anonymous users etc. for a start-up open-source software company, ABC. The company should have an internal CVS server (only internal developers can access it), an anonym..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the rate of heat loss from the steam pipe

Taking the temperature of the surrounding surfaces to be 20°C also, determine the rate of heat loss from the steam pipe.

  A room in the lower level of a cruise ship has a 30cm

a room in the lower level of a cruise ship has a 30cm diameter circular window.if the midpoint of the window is 4m

  Consider a gas turbine with turbine staging and reheating

consider a gas turbine with turbine staging and reheating. it operates under the following conditions.inlet air at 285

  Determine the maximum tensile stress st

Determine the maximum tensile stress σt(due to pure bending about a horizontal axis through C by positive bending moments M) for beams having cross sections as follows (see figure).

  Consider an iron-carbon alloy that contains 02 wt c in

consider an iron-carbon alloy that contains 0.2 wt c in which all the carbon atoms reside in tetrahedral interstitial

  Maximum velocity in the boundary layer

(a) Estimate the boundary layer thickness at a location 0.25 m measured from the lower edge. (b) What is the maximum velocity in the boundary layer at this location and at what position in the boundary layer does the maximum occur?

  At what point does the benefit of having the last stage

several methods have been tried to eliminate the droplets of condensed steam that hit and erode the last-stage blades

  When kaolinite clay al2si2o5oh4 is heated to a sufficiently

when kaolinite clay al2si2o5oh4 is heated to a sufficiently high temperature chemical water is driven off.a under these

  Medical applications of mems technology

Using the Internet, identify at least five medical applications of MEMS technology. In each case, explain the scientific and technological basis for the application, discuss the state of current research, and determine how close the technology is ..

  Water at 20c flows through at 10cm inner dyameter pipea

water at 20c flows through at 10cm inner dyameter pipe.a static pressure tap of a pilot tube at a cross section

  Transferred between piston cylinder device and surroundings

A piston cylinder device contains 1 kg of steam at 500C and 2 MPa. The piston device is surrounded by a water vapor mixture with a quality of x=0.6. What is the maximum amount of heat that can be transferred between the piston cylinder device and the..

  Compare inlet steam mass and volume flow rates in pound mass

Compare the inlet steam mass and volume flow rates in pound mass per second and cubic feet per second of (a) a fossil-fuel power plant turbine having a polytropic efficiency of 0.90 and receiving steam at 2400 PSIA and 1000F and (b) a nuclear power p..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd