Calculate the value of the led current

Assignment Help Electrical Engineering
Reference no: EM13999071

The diagram of FIGURE 2 shows a bi-directional opto coupler input interface circuit. When a supply voltage of 20 V is applied the LED carries a current and 2 V is dropped across it. Calculate the value of the LED current and the value of current through the 3kΩ resistance.

1734_internal.png

Reference no: EM13999071

Questions Cloud

Assuming that the equipment was purchased at the beginning : Discuss the ethical dilemma Alice faces in determining the treatment of the $30 million equipment purchase.
What research was reported in the news article : Were any psychological issues covered? What research was reported in the news article to support their approach to the health issue
Does the company have any other options under ifrs : How does Cadbury value its property, plant, and equipment? Does the company have any other options under IFRS for valuing these assets? How do these options differ from U.S. GAAP?
What are the basic principles of gestalt psychology : What are the basic principles of Gestalt psychology, and why was it important in the early life of psychology? What areas do you think were the Gestalt principles and avenues of research best suited for in modern psychology
Calculate the value of the led current : The diagram of FIGURE 2 shows a bi-directional opto coupler input interface circuit. When a supply voltage of 20 V is applied the LED carries a current and 2 V is dropped across it. Calculate the value of the LED current and the value of current t..
What is the specific heat of the alloy : A 60.0 g glass Container Contains 100 g of water all at 20.0 oC. A 40.0 g piece of alloy at 90 oC is added to the water in the Container. The final temperature of the mixture is 23 oC. What is the specific heat of the alloy, in cal/g oC
How is the fixed asset turnover ratio computed : How is the fixed-asset turnover ratio computed? How would you interpret National's ratio of 2.87?
Characteristic of sound : Cymatic Lighting or "visual sound" uses lighting to give cues as to the characteristic of sound. Qualities of sound such as frequency and bountifulness are mapped to similar qualities of luminance and chromaticity via algorithms
Determine the probability of a spin flip in z : What are the eigenvalues for energy, and the corresponding eigenvectors? Determine the probability of a spin flip in z, i.e. calculate P+ = | |2 and sketch your result as a function of t.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Construct a circuit using virtual breadboarding in multisim

Replace the transistor to a PNP transistor and the VCC to -12 V. Repeat Part A through Part C. Part F- Based on your observation and measurement of the components above, describe your conclusion about this the circuit

  Find the magnitude of the current supplied by the source

Two Loads are in parallel with a 2000 Volt sinusoidal source.Load 1 draws 40 Amps at 0.5 lagging power factor. Load 2 draws 15Amps at 0.8 leading power factor. (a) Make a table showing each load and its complex power

  Find vc in terms of the arbitrary constants c1 and c2

Consider an RLC circuit with R = 5 Ohms, L= ½ H, C= 2/9 F and input voltage e(t) = exp(-t/2)a. Starting from KVL show that the DE for the voltage across R is given by: v'' + 10 v' + 9 v = -5 exp(-0.5 t) b. Find vc in terms of the arbitrary constants ..

  What range of resistance values are limited by power

The maximum ratings for all resistors of this type are 250 (V) and ½ (W). What range of resistance values are limited by the maximum voltage rating of 250 (V), and what range of resistance values are limited by the maximum power of ½ (W)

  Design current-source circuit to provide an output current

Using VDD = 1 .8 V and a pair of matched MOSFETs, design the current-source circuit to provide an output current of 200μA nominal value. To simplify matters. assume that the nominal value of the output current is obtained at Vo ≈ VGS.

  Obtain the mathematical model of the opamp circuit

Home toaster suggest a closed loop control scheme to control the amount of browning on the toast and obtain the mathematical model of the OPAMP circuit

  What is the relative permittivity er of the dielectric

Will the electric field inside change (how much if yes)? Will the stored energy in the capacitor change (how much if yes)?

  Determine a suitable sampling frequency

Determine a suitable sampling frequency. Design a notch filter to remove the 50Hz component, paying particular attention to any assumptions you have made in the design.

  Write a matlab function to generate gray coding matrix

Write a matlab function to generate Gray coding matrix. The function has one input M where M=2^m and m is the number of bits per symbol. For example, if the function my_graycoding(4), the output should be

  Determine the psf of an ideal low pass anti aliasing filter

We want to sample the 2-D continuous signal f(x,y)=exp{-\(pi(x^{2}+y^{2})\)} by means of a rectangular sampling scheme to obtain 1.5 samples per millimeter. Determine the PSF h(x,y) of an ideal low pass anti aliasing filter

  What are the possible power levels pi at the outputs

Suppose the above device is to be used as an 8-way power splitter (let's say only the top-most input is used). Let the input power be P. Assuming a cross-coupling coefficient of f and ignoring excess losses, what are the possible power levels Pi a..

  Define nmos fet and bjt analysis

A standard silicon NPN BJT is to be used as an amplifier. The emitter voltage is biased at 4 volts, the base is biased at 5 volts, and the collector is biased at 10 volts. Will this circuit perform as desired? Why or why not.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd