User Account

All Pages

Calculate the value of convection coefficient

Assignment Help Mechanical Engineering
Reference no: EM132641294

Calculate the value of convection coefficient required to cool the alloy steel balls (15 mm diameter, density = 8000 kg/m3, specific heat = 500 J/kgK, conductivity = 50 W/mK) from 820°C to 100°C. The bathing temperature is 40°C and the process must be completed in 5 min, 10 min and 30 min. Draw the relationship between time and heat transfer coefficient

Reference no: EM132641294

Questions Cloud

Conduct a literature review on a particular developmental : Conduct a literature review on a particular developmental disability that interests them. Students will choose their own topics. Describe the etiology
Describe the methods of checking components : Describe the methods of checking components are fit for purpose, and how to identify defects and wear characteristics
What amount should be classified as general expenses : The office space is used equally by the sales and accounting departments. What amount should be classified as general and administrative expenses
Which is not a good example of the matching principle : Which is not a good example of the matching principle? Recognition of revenue for which associated expenses cannot yet be determined is delayed until.
Calculate the value of convection coefficient : Calculate the value of convection coefficient required to cool the alloy steel balls (15 mm diameter, density = 8000 kg/m3, specific heat = 500 J/kgK, conductiv
Calculate the speed of the axe : The axe gets stuck into the log, and the log swings. Calculate the speed of the axe, in m/s, if the swing angle is 40°
Make a case that provision of gaap should not be changed : Argue either that GAAP should be changed to require liabilities such as this to be recognized, or make a case that this provision of GAAP should not be changed.
How is your country legally prepared for an incident : Use the internet to locate the membership information regarding the Local Emergency Planning Committee for your county(Decatur County). List the names.
Determine the issues raised in the readings : Determine the issues raised in the readings, and in your personal observation and study, that you will focus on in your case study analysis

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the combined stresses at the outer edges aa and bb

A short compression member is subjected to a compressive load of 25,000 lb at an eccentricity of 1.5 in., as shown. The member is 6 in. by 8 in. in cross section. Calculate the combined stresses at the outer edges AA and BB.

  Explain what is the amplitude of the response x

In the idealized model attached shown, m = 15 kg, k = 135 N/m, and the viscous damping ratio is 0.15. Assume that an external harmonic force F(t) = 15 cos 4 t acts on the system with F0=15 N and forcing frequency of 4 rad/s.

  Microwave do job more efficiently and quicker

1. Baking a potato takes a long time, even in a hot oven, because the inside of a potato warms up very slowly.  e. Why Can a Microwave do this job more efficiently and quicker?  f. What is a potato clock and why does it work?

  Find and show the reaction components on a drawing

The figure shows an N-truss girder, loaded by concentrated vertical forces of magnitude 3P at the joints F and J, and of magnitude 6P at the joints G, H and I. All bars are elastic with stiffness EA.

  Calculate the manometer reading h

Calculate the manometer reading H for a pressure of 30 psi in the air pipe. Assume an isothermal process for the air in the sealed tube.

  What is the mass flow rate of the refrigerant in the cycle

A heat pump uses r134a as the refrigerant to keep a heated space at 20°c by pumping from a geothermal water source. Water from the geothermal source enters the evaporator (a heat exchanger) at 50°c and leaves at 40°c at a rate of 0.08 kg/s. The re..

  Consider a cogeneration power plant modified with

consider a cogeneration power plant modified with regeneration. steam enters the turbine at 9 mpa and 400 c and expands

  Determine the required speed and diameter of the machine

A hydroelectric site has available HT 80 m and Q = 3 m3 /s. It is proposed to use a Francis turbine unit with the operating characteristics at optimum efficiency shown in Fig. 12.24. Determine the required speed and diameter of the machine.

  Calculate the pressure of air inside the cylinder before

a well-insulated vertical piston-cylinder device contains air. the diameter of the piston is 8 inches. atmospheric

  Determine the rate of entropy production

For a control volume including the turbine and a portion of its immediate surroundings so that the heat transfer occurs at the ambient temperature, 40°F, determine the rate of entropy production in Btu/ °R per lb of air passing through the turbine..

  What is the air pressure in the closed chamber b

Perform a dimensional analysis to determine the dimensionless groups that would be required to define the pump performance. Arrange the groups so that the power and pump pressure each appear in only one group.

  If you make 100 tones of ice per month 1 month 30 days

you have a refrigeration plant that makes ice in the summer to supply grocery stores. you maintain the cold room where

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd