Calculate the total cable resistance due to both wires

Assignment Help Electrical Engineering
Reference no: EM13267830

1. A dc power distribution cable has two #6 copper wires. The copper wire table in the textbook lists each wire as having resistance of Ro=.4028 ohms per thousand feet at temperature of 25C. The temperature coefficient of copper is alpha=.004 per C. IF the cable is expected to operate at 75C, then the resistance would be R = Ro +Ro(alpha)(delta*T), where delta*T=50C is the temperature rise above 25C. If the cable is 455 feet long, calculate the resistance of each wire at 75C. Calculate the total cable resistance due to both wires.

2. A DC source of 48V is connected to one end of the cable. The other end of the cable supplies a DC load. If the load current is 12.5 A, calculate the voltage drop due to the cable resistance and the laod voltage. Assume the cable temerature is &%C. Sketch the circuit and label all the voltages on the sketch.

Reference no: EM13267830

Questions Cloud

Determine what is the mod number of the counter : A synchronous binary counter is used to divide a 1 MHz input frequency to 3.90625 kHz. What is the MOD number of the counter and how many flip-flops are required
What were the capitulations in the ottoman empire : What were the Capitulations in the Ottoman Empire? What consequences did they have and define the termmamluk, and discuss why the Mamluk system of government was a success in the Middle East for over 250 years
What is the projected incremental operating cash flow : What is the projected incremental operating cash flow of the machine in each of years 1 to 5?
Why is the yield on bond c different : If bond C is considered identical to bond B except for the conversion privilege, what is the value of the conversion privilege? Does the conversion privilege benefit the issuer of the bond or the purchaser? Is this consistent with the price you ca..
Calculate the total cable resistance due to both wires : A dc power distribution cable has two #6 copper wires. The copper wire table in the textbook lists each wire as having resistance of Ro=.4028 ohms per thousand feet at temperature of 25C. The temperature coefficient of copper is alpha=.004 per C.
What is annual yield to maturity : you are about to invest in a 10 yr 8% semiannual bond. The bond is selling at $980.What is annual yield to maturity.
What was the non-controlling interest''s share of sparis : Net income for Sparis was $912,000 during 2010. What was the non-controlling interest's share of Sparis' net income for 2010?
What are the total annual ordering costs : Amistad Inc manufacturers custom golf clubs and orders 250,000 graphite shafts per year from its manufacturer. The CEO at Amistad wishes to know the optimal EOQ. The carrying cost is $.45 per shaft per year. The order cost is $750 per order.
What current flows through the resistor for the resistance : The bottom of the conduction band at one end of a silicon resistor is at the same energy level as the top of the valence band at the other end. What current flows through the resistor if the resistance is 1.12 kOhms

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine what is the sampling frequency in a dsp system

The sampling frequency in a DSP system is fs=8 kHz. Anti-aliasing filter used in the system is the second-order Butterworth filter with cutoff frequency of fc=3.4 kHz. What is the percentage of aliasing level at the frequency f=2.5 kHz

  Determine what is the value of source current

An input signal of 10V at 0o is applied to a parallel RLC circuit with resistor R = 100 , inductive reactance XL = 100 , and capacitive reactance XC = 200 . All three components are connected in parallel to the source. what is The source current.

  What is the binary value on the a-d output pins

An 8-bit A/D converter has Vref- = 2 V and Vref+ = 5 V. The analog input signal vin has a frequency range of 300 Hz to 3.4 kHz. a) If vin = 7 V, what is the binary value on the A/D output pins b) If vin = 1 V, what is the binary value on the A/D outp..

  Determine whether the given signals are periodic

Determine whether the following signals are periodic. If they are, find the smallest periods (fundamental periods). a) f(x,y) = sin (2 pi x) cos(4 pi y) b) Discrete signal: f(m,n) = sin ( pi * m / 5) cos(pi * n / 5)

  Calculate the thermal efficiency and compare it with carnot

A Rankine cycle power plant steam enters the turbine at 100psia and 800deg F.. Heat is rejected in the condeser at 80deg F. Isentropic sxpansion and compression occurs in the turbine and pump respectivel

  Derive an expression for the built-in voltage

Consider a p-type semiconductor substrate with Na =10^15 cm^-3. A region of heavily p+ doped material is formed by ion implantation as shown in the sketch below.Derive an expression for the built-in voltage under equilibrium conditions.

  Discuss how narrowing bandwidth of circuit affects noise

Looking at a sine wave, describe how the ROM in a DDS could use only one-fourth of the memory locations to store the sine wave look-up table. Discuss how narrowing the bandwidth of a circuit affects the noise level.

  Develop the pseudo-code

Develop the pseudo-code below for a program that will retrieve 2 bytes (NUM1 and NUM2) from memory, determine which is closest to the numeric value 50, and indicate the result by setting a variable named "CLOSEST" to 1 (if 1st byte is closest) or ..

  Determine at what speed should the machine be operated

A 450 piece/hr 10 hr B 500 piece/hr 8 hr A set of unsharpen ed tools costs $1,500 and can be ground 15 times. The cost of each grinding is $20. The time required to change and reset the tools is 2 hours, and such changes are made by a tool-setter.

  Calculate the natural frequency of oscillation

The bellows, diaphragm, and Bourdon tube pressure sensors all exhibit second order time response. This means that a sudden change in pressure will cause an oscillation in the displacement and, therefore in the sensor output.

  Determine the force density and magnetic flux

A current density J¯ = ˆy sin(2x) A/m^2 is subject to a z-directed magnetic field H¯ = ˆz10 A/m. a. Assuming the vacuum permeability (i.e. a non-magnetic medium), what is the magnetic flux

  Define the gain of the antennas must be increased

The gain of the antennas must be increased when the TDMA system described in part (d) is used because the bit rate is higher than with FDMA and the noise power in the receiver is therefore higher

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd