Calculate the time required at the carburizing temperature

Assignment Help Mechanical Engineering
Reference no: EM13641762

A piece of 0.1% C steel is to be carburized at 930C until the carbon content is raised to 0.45% C at a depth of 0.020 in. (0.050 cm). The carburizing gas holds the surface composition at 1% carbon for all t > 0. If D=1.4 x 10^-7 cm^2/sec: (a) Calculate the time required at the carburizing temperature. (b) What time is required at the same temperature to double this amount of penetration? (c) If D=0.25 exp(-34,500/RT) cm^2/sec, what temperature is required to get 0.45% C at 0.040 in. (0.10 cm) in the same time as 0.02 in. was attained at 930C?

Reference no: EM13641762

Questions Cloud

An experiment consists of choosing a subset from a fixed : an experiment consists of choosing a subset from a fixed number of objects where the arrangementorder of the chosen
If he shot a dart at an antelope at rest 50 m away and the : once upon a time a famous zoologist was hunting antelope for a zoo with a dart gun that fired darts with a range of 100
The three capacitors c3010-6 f in series are connected : the three capacitors c3.010-6 f in series are connected across a 30-v battery.a find the charge on each capacitorb find
Steam enters a turbine at a pressure of 10 bar and : 1 steam enters a turbine at a pressure of 10 bar and temperature 360 degree c. it exists the turbine as saturated vapor
Calculate the time required at the carburizing temperature : a piece of 0.1 c steel is to be carburized at 930c until the carbon content is raised to 0.45 c at a depth of 0.020 in.
A series combination of a 14 k resistor and an unknown : a series combination of a 14 k resistor and an unknown capacitor is connected to a 11 v battery. one second after the
Discuss the validity of the use of the semi-infinite case : a bar of steel 10 cm x 10 cm x 100 cm has an initial carbon content of 7.6 x 10-3 gmcm3. at t0 the surface of the bar
A box contains 24 yellow 32 green and 36 red jelly beans if : a box contains 24 yellow 32 green and 36 red jelly beans. if 15 jelly beans are selected at random what is the
Plate 3 moves at 3 m s-1 find the velocity of plate 2 at : three parallel flat plates are separated by two fluids. plate 1 on the bottom is at rest. water viscosity 0.8007 cp at

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A steel thermal diffusivity 000001172 k43 cylinder 10 cm in

a steel thermal diffusivity 0.00001172 k43 cylinder 10 cm in diameter and 10 cm long is initially at 300degc. it is

  When the three blocks are released from rest they

when the three blocks are released from rest they accelerate with a magnitude of 0.660 ms2. block 1 has mass m block 2

  What is the minimum plate length that should be used at

a fan that can provide air speeds up to 50ms is to be used in a low-speed wind tunnel with atmospheric air at 25 degc.

  To understand the physics of the o-ring we may need to

to understand the physics of the o-ring we may need to start formulating the problem in a static equilibrium condition.

  Determine the smallest horizontal force required to pull

determine the smallest horizontal force required to pull out wedge a. the crate has a weight of 200 and the coefficient

  Air at 15 c ows over a at plate a heater strip 10 cm long

air at 15 ? c ?ows over a ?at plate. a heater strip 10 cm long is placed on the plate at a distance 15 cm from the

  How many square feet of collector would be required for a

the collecting panels of a solar boiler receive energy as heat at the rate of approximately 300 btuhr-ft2 of collecting

  A load of 275x106 g produces a 0327 cm diameter impression

a brinell hardness measurement is made on a nickel alloy using a 0.01 m diameter sphere of tungsten carbide. a load of

  Preparing cad geometry for fea

Demonstrate suitable accuracy by using a simple hand calculation for the static analysis of the structure. Describe in detail the hand calculations performed to validate the final solution. What is the approximate error between the simplified hand..

  An airplane wing modeled as a spring-mass system with

an airplane wing modeled as a spring-mass system with natural frequency 40 hz is driven harmonically by the rotation of

  A brayton cycle inlet is at 300 k 100 kpa and the

a brayton cycle inlet is at 300 k 100 kpa and the combustion adds 670 kjkg. the maximum temperature is 1200 k due to

  How much pressure is required for a force output of 62275

1. how much pressure is required for a force output of 62275 newtons if the effective piston area of the cylinder is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd