Reference no: EM13875198
Scenario
As part of a design engineering team working on building a new ship, you are expected to carry out simple calculations to determine what will happen to the ship at sea water with different density. A simplified version of this scenario is presented in Task 1.
Learning Outcome 1
1: Determine the hydrostatic pressure and thrust on immersed surfaces
1) A plastic cube that can be used to design a ship (illustrated in figure 1)has a dimension of 10 cm on each sideand mass 0.20 kg, with appropriate calculations explain:
a. What happens if the cube is placed in salt water (ρ = 1050kg/m3)?
b. What happens if the cube is placed in fresh water (ρ = 1000kg/m3)?
Determine the volume of the water displaced and the submerged depth in (m) in questions (a) and (b) above. Explain also the difference in the answers obtained in (a) and (b) above.
2) A cylindrical steel drum is to be used as a buoy in sea water (ρ = 1050 kg/m3). The drum is 700mm in diameter and 1100mm long and has a mass of 250kg. It is required to float two thirds (2/3) submerged, as shown in Figure 2 below.
a. Calculate the hydrostatic pressure on the drum and the weight of water displaced when the buoy floats 2/3 submerged.
b. Calculate the mass which must be placed in the bottom of the drum to ensure that it floats 2/3 submerged.
Learning Outcome 2
1.2: Determine the centre of pressure on immersed surfaces
3) A tank is 500mm by 1100mm in plan and contains water (ρ = 1000 kg/m3) to a depth of 350mm. Calculate the total hydrostatic thrust force and depth to the centre of pressure for:
a. The shorter side, and
b. The longer side.
c. Comment on your findings.
4) A tank of fuel (ρ = 850 kg/m3) has a circular valve, 0.40m in diameter, which opens when the level of fuel in the tank reaches 1.35m above the hinge. The valve is kept closed by a spring, mounted on the lower edge of the valve, as shown in Figure 3 below.
a. Calculate the thrust on the valve and the depth to the centre of pressure, shown as y in the figure.
b. Calculate the minimum force required in the spring to hold the valve closed at the required level.
Learning Outcome 3
1.3: Determine the parameters of devices in which a fluid is used to transmit force
A hydraulic press is required to deliver a force of 90kN onto the work surface as shown in Figure 4 below. The piston in the press has a diameter of 320mm.
a. The maximum force which can be applied at the input piston is 1750N. Calculate the optimum diameter of the input piston which will allow the press to operate. Again, ignore any frictional losses.
|
Identify strategies and communication tools to be used
: Identify strategies and communication tools to be used in the process- including technology
|
|
Identify education,key interrelationships with professions
: Select a disease process from among the following-Diabetes,Obesity and Coronary artery disease
|
|
Repudiation released her from her duty to perform
: Moore contracted in writ- ing to sell her 2012 Hyundai Santa Fe to Hammer for $16,500. Moore agreed to deliver the car on Wednesday, and Hammer promised to pay the $16,500 on the following Friday. Moore contended that Hammer’s repudiation released he..
|
|
Bottom and the mass of the piston
: Two tanks contain steam, and they are both connected to a piston/cylinder. Initially the piston is at the bottom and the mass of the piston is such that a pressure of 1.4 MPa below it will be able to lift it.
|
|
Calculate the thrust on the valve and the depth
: Calculate the optimum diameter of the input piston which will allow the press to operate and determine the centre of pressure on immersed surfaces
|
|
Calculate the standard deviation of the returns
: An entity has a stock that has a beta of 1.20 when the risk free rate is 5% in 2010. The average return on the market in 2010 was 12%. In 2011 the risk free rate increased by 1% due to inflation, but the return on the market increased by 2%. Calculat..
|
|
Describes a quality assurance process for ongoing training
: Create a Support Model (MS Visio) that describes a quality assurance process for ongoing training, problem reporting, tracking, escalation, and resolution once your selected project is complete and the technology solution is transitioned to operat..
|
|
Evaluate the liquidity and profitability of blue water yacht
: Evaluate the liquidity and profitability of Blue Water Yachts using selected financial ratios. Assess the company's overall profitability, liquidity, and desirability as an investment.
|
|
What is the annual loan payment
: The S Company is considering the acquisition of a new processor used in its operation. The processor has an installed cost of $55,000 and is expected to have a useful life of 5 years. If purchased, the firm would borrow the entire $55,000 at an inter..
|