Calculate the tension in the string

Assignment Help Mechanical Engineering
Reference no: EM131394260

a particle of weight 24N is attached to one end of a string 1.3m long whose other end is fastened to a point on a vertical fall. a horizontal force acting on the vertical keeps it in equilibrium 0.5m from the rope. calculate the tension in the string and the magnitude of the horizontal forces

Reference no: EM131394260

Questions Cloud

Write a few sentences describing given wine prices : Which lake region produces the cheapest wine?- In which region are the wines generally more expensive?- Write a few sentences describing these wine prices.
Where is the insulation temperature greatest : If the convection coefficient on the interior side of the wall is 5 W/m2-K and the interiortemperature is 21oC, determine the rate of heat loss through the wall
Find the interior heattransfer coefficient : Find the interior heattransfer coefficient. Is heat transfer best on the interior or exterior surface of the stack? Explainyour answer.
Write a memo supporting one proposal over the other : BUS 300- Write a memo supporting one proposal over the other with the following in mind: The City Council wants to reduce traffic in the downtown/campus area.
Calculate the tension in the string : calculate the tension in the string and the magnitude of the horizontal forces
Summarize about fuel economies of given two types of vehicle : Combined Fuel Economy (using an average of driving conditions) in miles per gallon by whether the car has two- or four-wheel drive. Summarize what you see about the fuel economies of these two types of vehicles.
Find the mechanical behaviour of intervertebral discs i : Compute the cable tensions and RA.
Summarize what you see about the fuel economies : Here is a boxplot of Combined Fuel Economy (using an average of driving conditions) in miles per gallon by vehicle Type (car, van, or SUV). Summarize what you see about the fuel economies of the three vehicle types.
Calculate the force of attraction between these two ions : Calculate the force of attraction between these two ions at their equilibrium inter-ionic separation (i.e., when the ions just touch each other).

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A static thrust structure is to be designed for a turbofan

a static thrust structure is to be designed for a turbofan engine. the following standard engine test conditions are

  Find the velocity of the wind

A plane can fly 305 mph in still air. If it can fly 185 miles downwind in the same amount of time it can fly 120 miles upwind, find the velocity of the wind.

  Gear is put in neutral on level road without wind resistance

The rolling resistance of a 1200kg car depends on its weigh as F = 0.006m x gravity. How far will the car roll if at 90km/h the gear is put in neutral on a level road without wind resistance?

  A system consists of two blocks, of masses m

A system consists of two blocks, of masses m and 2m, attached to the ends of a mass less spring with a force constant k. The system is placed on a horizontal friction-less surface. Initially, the spring is relaxed. The blocks are then pulled apart an..

  Determine the maximum allowable uniform load w that can be

determine the maximum allowable uniform load w that can be supported by the fiberglass beam if b 125 mm and the

  What would be the deflection of the spring

How many equations do you think are needed to describe this system mathematically? If the system ever came to rest, what would be the deflection of the spring?

  A diffuser shown in fig p636 has air entering at 100 kpa

a diffuser shown in fig. p6.36 has air entering at 100 kpa 300 k with a velocity of 200 ms. the inlet cross-sectional

  The viscosity of the water is 112x10-3 pa s determine the

a 60 cm wide conveyer belt is driven over a 2mm film of water. determine the resultant force required to keep the belt

  Determine the exit temperature

Steam enters an adiabatic nozzle steadily, at 2.5 Mpa and 400°C with a velocity of 50 m/s and exits at 1 MPa and 380 m/s. If the nozzle has an inlet area of 65 cm2, determine: The exit temperature. The rate of entropy generation for this process, in..

  Explain the chemistry of the analytical method

Explain the chemistry of the analytical method.

  Determine the center lcl and ucl for the p chart

The yield of good chips during a certain step in silicon processing of integrated circuits averages 91%. The number of chips per wafer is 200. Determine the center, LCL, and UCL for the p chart that might be used for this process.

  Determine the quality of the mixture the mass of liquid and

a 1 m3 rigid vessel contains 1 kg saturated liquid plus vapor h2o at 100oc. determine the specific volume of the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd