Calculate the tension in the rope in newtons when you lift

Assignment Help Mechanical Engineering
Reference no: EM13635669

Your friend, a 75 kg mountain climber is suspended from a cliff by a rope. Calculate the tension in the rope, in Newtons, when you lift your friend to safety. If the rope can withstand 1.25 kN of stress per square centimeter of cross-sectional area, what minimum diameter of rope (cm) is needed so that your friend does not fall into the abyss? What factor of safety would you want to apply to this diameter to be very, very sure that this rope will not break (1.5x 2x, 3x, 10x, 100x, 1000x)?

Reference no: EM13635669

Questions Cloud

A 15 m long string of mass 18 kg is streched such that the : a 15 m long string of mass 1.8 kg is streched such that the tension in the string is 25 n. a wave of frequency 20 hz is
You want to make the buffer but you find you are out : the most common buffer in mammalian tissue culture is aphosphate buffer. the three pkas of phosphoric acid are 2.167.21
Find the indicated probabilities using the geometric : find the indicated probabilities using the geometric distribution or the poisson distribution. then determine if the
A 05kg block at rest on a table is attached to a : a 0.5kg block at rest on a table is attached to a horizontal spring with a spring constant k200 nm. the spring is
Calculate the tension in the rope in newtons when you lift : your friend a 75 kg mountain climber is suspended from a cliff by a rope. calculate the tension in the rope in newtons
One biochemical reaction has a standard gibbs energy : one biochemical reaction has a standard gibbs energy of-200kjmol and a second biochemical reaction has a standard
If the pipe is to be insulated with glass wool insulation : chilled water enters a thin shelled 4 cm diameter 200 m long pipe at 7 deg. celsius at a rate of 0.98 kgsec and leaves
Oxygen gas is collected overwater at a temperature of 10 c : oxygen gas is collected overwater at a temperature of 10 c and a pressure of 1.02 atm. the volume of gas plus water
The following is a histogram that is a graph that : the following is a histogram that is a graph that represents all the numbers drawn in the california lotto daily 3

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine exit temp of oil and heat transfer rate between

consider a shell and tube heat exchanger which is used to heat water cp water 4.33kjkgk from 10 deg c to 85 deg c

  A solar hot-water system stagnates at 85 c under

a solar hot-water system stagnates at 85 c under insolation of 740 wm2 and an ambient temperature of 17 c. find its

  Steam at 95 bar and 400 c is supplied in turbine the

steam at 95 bar and 400 c is supplied in turbine. the condenser pressure is 0.035 bar. if the plant operates as a

  Estimate the smallest diameter of a rod

The compression strength of Kevlar 49 fiber is about one-eight of its tensile stress. Estimate the smallest diameter of a rod on which 12 um diameter Kevlar fiber can be wound without causing kinks on its compression side.

  Given a tank with 60 cm of crude oil sg086 on top of 200 cm

given a tank with 60 cm of crude oil sg0.86 on top of 200 cm of water both at 50 degrees c. barometric atomospheric

  A carnot engine operates between two reservoirs maintained

a carnot engine operates between two reservoirs maintained at 400 degrees celcius673.15k and t2 respectively. the heat

  Find addendum dedendum clearance circular pitch circular

preliminary design calculations have suggested that design objectives may be met by a straight spur gearset using

  Calculate the thermal efficiency of the cycle and the net

consider an ideal steam regenerative cycle in which steam enters the turbine at 600 lbfin2 700 f and exhausts to the

  Exhaust gases enter the regenerator at a pressure of 140

air enters a regenerator at a pressure of 1mpa temperature of 550 k and mass flow rate of 800 kkgmin. heat is

  During a 100 m sprint usain bolt reaches his maximum speed

during a 100 m sprint usain bolt reaches his maximum speed in 2 seconds from rest with constant acceleration. he then

  Calculate a the work done in going from state 1 to 2 b the

an ideal gas of mass 2 kg is contained within a rigid cylinder and undergoes a cycle which consists of three separate

  The material is a low carbon steel bhn of 200 with a

a turning operation calls for a single pass on a 3 diameter part down to 2.800 on a lathe using a hss high speed steel

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd