Calculate the temperature of the gas in the tank when the

Assignment Help Mechanical Engineering
Reference no: EM13344391

During an emergency launch operation, to fill a missile with RP-4 (a kerosene-based fuel), the ullage volume of the fuel storage tank is pressurized to 10.34 bar with air coming from a large external storage tank at high pressure (69 bar). This operation is to be completed as rapidly as possibleThe fuel storage tank can be approximated as a right circular cylinder 12.2 m tall and 3.05 m in diameter and is originally filled to 90% of capacity. The initial conditions in the tank are T=300K and P=1 atm.
a. Assuming no mixing between the original and the incoming air, what problems would you anticipate if the inlet gas control valve were to malfunction and the gas space above the fuel were to reach full storage pressure (69 bar)? (The fuel tank has been hydrostatically tested to 276 bar.)
b. calculate the temperature of the gas in the tank when the pressure has reached 10.34 bar and if the valve does not fucntion properly and the pressure in the tank reaches 69 bar. for simplicity, consider the air to be an ideal gas with Cp=(7/2)R .

Reference no: EM13344391

Questions Cloud

A 200-kg 5-m-wide rectangular gate shown innbspthe figure : a 200-kg 5-m-wide rectangular gate shown innbspthe figure is hinged at b and leans against thenbspfloor at a making an
Use microsoft excel to compare costs from at least three : 1. use microsoft excel to compare costs from at least three different vendors and reasons to accept specific bids.
If 0176 moles of mg have combined with 0220 moles of o what : if 0.176 moles of mg have combined with 0.220 moles of o what is the empirical formula of the
Density measurements can be used to analyze mixtures for : density measurements can be used to analyze mixtures. for example the density of solid sand without air spaces is about
Calculate the temperature of the gas in the tank when the : during an emergency launch operation to fill a missile with rp-4 a kerosene-based fuel the ullage volume of the fuel
A solution of ethanol c2h5oh in water is prepared by : a solution of ethanol c2h5oh in water is prepared by dissolving 65.7 ml of ethanol density 0.79 gcm3 in enough water
The stomach to give carbon dioxide water and a soluble : a certain brand of antacid chewing gum was sent to the lab for testing and it was found to have 15 by mass of
If you used the 8900 kilojoules you expend in energy in one : if you used the 8900 kilojoules you expend in energy in one day to heat 51000 of water at 20 what would be the rise in
Once released into the atmosphere the so2 is likely to : once released into the atmosphere the so2 is likely to react with oxygen to form so3. what can happen next if the so3

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd