Calculate the surface area of a rectangular

Assignment Help Civil Engineering
Reference no: EM13211111

How will calculate the surface area of a rectangular open trench Length=100 mtr,Width=.6mtr,Depth= .75mtr.

Reference no: EM13211111

Questions Cloud

Define what is the partial pressure of the components : If the total pressure in the cylinder is 2430 mmHg, what is the partial pressure of each of the components? Assume constant temperature.
Define pancreatic lipases hydrolyze triacylglycerols : Pancreatic lipases hydrolyze triacylglycerols (triglycerides) that have been emulsified by bile. Modify the triacylglycerol below to show the products of its hydrolysis
Calculate the ratio of the area to volume for unit cube : calculate the ratio of the area to volume for unit cube,a unit sphare inscribed inside the cube,and as right cylinder inscribed inside the cube.
Plot the variation with depth : Plot the variation with depth (z) of the at-rest lateral earth pressure behind the wall, and determine the magnitude and location of the at-rest lateral earth force per unit length of wall.
Calculate the surface area of a rectangular : How will calculate the surface area of a rectangular open trench Length=100 mtr,Width=.6mtr,Depth= .75mtr.
Write computer code using matlab that emoloyes the nelder : write computer code using Matlab that emoloyes the nelder and mead simplex method to solve the welded-beam design (benchmark problem
What is the mass of the fish : A fish hanging from the bottom of the spring oscillates vertically at a frequency of 2.00 Hz. Ignoring the mass of the spring, what is the mass of the fish?
Inability and green engineering can be integrated : inability and green engineering can be integrated in the four components of materials science and engineering?
What is the purpose of a cost allocation system : Compare the profits and accuracy of all cost allocation schemes based on Tom Arnold's initial reason for being hired and what is the purpose of a cost allocation system?

Reviews

Write a Review

Civil Engineering Questions & Answers

  Magnitudes of the additional loads

Determine the magnitudes of the additional loads that must be applied at B and F if the resultant of all six loads is to pass through the center of the mat.

  Steps of dmaic abandoned

Assume that during the analyze stage an obvious solution is discovered. Should that solution be immediately implemented and the remaining steps of DMAIC abandoned?

  What type of contract would you want and why

If you were asked to perform an excavation contract competitively with limited data, what type of contract would you want and why?

  Determine the coefficient of friction

a mass of 2kilogram is projected with a speed of 3m/s.if a plane inclined 20 degrees with the horizontal.after travelling travelling 0.8meters, the mass comes to rest. determine the coefficient of friction and also the speed as the black returns t..

  Describe the application of geophysical techniques

Describe the application of geophysical techniques using electromagnetic induction as a tool for sustainable soil and water management of agricultural fields in the humid tropic Caribbean 300 word limit".

  Consolidation ratio of the soil at the unloaded condition

An increment of vertical stress of150kpa compress the sample to a void ratio of1.43. What is the over consolidation ratio of the soil at the unloaded condition.

  Projectile shot vertically upward

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  Describe the present land capability classification system

Describe the present land capability classification system for agriculture in the caribbean, Identifying its limitations and propose recommendations. 200 word limit

  Describe electron and hole motions in a p-n junction

Briefly describe electron and hole motions in a p-n junction for forward and reverse biases;

  Calculate the force

Calculate the force (in Kn) a punch press must exert if it is to punch out a large washer from a strip of 5-mm thick sheet steel with an ultimate shear strength of 400 MPa. The washer dimensions are as follows: hole diameter is 27 mm. outside diam..

  Shape of a circular arc

Rod AB is bent into the shape of a circular arc and is lodged between two pegs D and E. It supports a load P at end B. Neglecting friction and the weight of the rod, determine the distance c corresponding to equilibrium when a = 43mm and R = 143mm..

  Determine whether these conditions are true or false

Determine whether these conditions are true or false.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd