Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
Calculate the super-elevation required for a horizontal curve on a two-lane, two- way highway with 60 mph design speed, and a 1200 ft. radius curve. What is the required length of the spiral curve? If the lane width is 12 ft, and the cross (side) slope of the crown section is 2.0%, draw to a convenient scale the progress of pavement edges to attain the superelevation. Revolve the pavement about its
a. Inside edge. b. Outside edge c. Centerline
a circular aluminum tube of L=600 mm is loaded in compression by forces P. The outside and inside diameters are d2=75 mm and d1=63mm, respectively. A strain Gage is placed on the outside of the tube to measure normal strains in the longitudinal di..
Compare the stoichiometric air/fule ratios (AFR) for complete combustion of Benzene (C6 H6), Octane (C8 H8), and Ethanol (C2 H5 OH) in air (O2 + 3.76 N2). The only products should be CO2, H2O and N2.
The intensity of Na light passing through a gold film wasmeasured to be about 15% of the incoming light. What is thethickness of the gold film? ( λ=589 nm; k=3.2).
Axis Chemical Company needs you to design a gravity sewer to convey 1,750 GPM of toxic waste. The pipe is to be glass-lined reinforced concrete (n = 0.009). Which pipe would you suggest the Joker use
An irrigation channel is constructed of earth and is 8.1km long and has a capacity of 10 m^3/s for a flow depth of 2m. The cross section is trapezoidal with a bid width of 8 m and side slopes of 2 horizontal to 1 vertical.
When 0.3 m^3/s water flows through a 150 mm constriction in a 300 mm horizontal pipeline, the pressure at a point in the pipe is 345 kPa, and the head loss between this point and the constriction is 3 m.
how to design a simply supported rectangular concrete beam having cross section of 20 mm by 40 mm and a length of 3 meters that couldcarry a uniform load of 1000 KN
A Riehle Impact Testing Machine was used to break the specemins and the reading gave 68ft/lb, 66ft/lb, 64ft/lb, 69ft/lb and 63ft/lb. The cross section dimensions of the Charpy were measured to be 0.320in and 0.397in.
Terry wants to purchase a used car for $8000. The dealer offered to finance the deal at 8.5% APR for 4 years with 10% down payment. Terry's bank will provide a loan at 7.8% for 3 years, but wants a 20% downpayment.
Successive plus and minus sights taken on a downhil line of levels are listed below. the values represent the horizontal distances between the instrument and either the plus or minus sights.
The grains of wood in the board make an angle of 20 degrees with the horizontal as shown. Determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of 250 N.(Dimensions l=3..
How long would it take to fill a 30 yd^3 packer truck that compresses waste to 750 lb/yd^3 if it travels 100 ft between stops at an average of 5mph and it takes 1 minute to load 200 lb of waste at each stop
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd